Coherent

Search Results

37 - 48 of 88 Products for 'detector' Page 4 of 8 |

detector

COHR MephistoMOPA DS 0417 2.pdf

COHR MephistoMOPA DS 0417 2.pdf

…-130
-120
-110
-100
10k
Frequency (MHz)
100k 1M 10M
RIN (dB/Hz)
Free Running
Noise Eater Active
Detector Noise
Frequency (THz)
281.605
281.610
281.615
281.620
281.625
281.630
281.635
281.640
281.645…

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf


The light intensity of a Gaussian line fades away towards the ends of the line, eventually falling below the
threshold level of the detector and becoming invisible
Non-Gaussian Lines are Easy to Calibrate
Because the light intensity of gaussian lines is nonuniform, the…

MiraHP DS 2.qxd

MiraHP DS 2.qxd

…View Features · High-power modelocked output · OptimaTM control & diagnostics package - Fast photodiode - Autoranging power monitor detector - CW detector - Automatic modelocking starter - -LockTM automatic GTI control · Integrated pump beam steering optics · Multiple pump port options ·…

Quotation KML QGYYMMDD G  Institute Contact

Quotation KML QGYYMMDD G Institute Contact


them is to block all background light from impinging on the detector, both at the fundamental
driving laser wavelength of 800 nm, and at harmonic wavelengths that are within the detection
range of the detector, but outside
range of wavelengths that are
spectrally resolved.…

EnergyMax-USB-RS-Sensors-Guide FORMFIRST.pdf

EnergyMax-USB-RS-Sensors-Guide FORMFIRST.pdf

…Low noise and excellent linearity for greater accuracy
· Large active area
Unlike all other thermal detectors, pyroelectrics measure
the rate of change of the detector temperature, rather
than the temperature value itself. As a result, the response
speed of the pyroelectric…

00 E-250 Pre.book

00 E-250 Pre.book

…a calibrated optical
power meter (detector head plus display console) is necessary.
Liquid (water) cooling is generally required for the detector head at
E-250 Series power levels. Make sure to provide adequate cooling
for the detector head.
Coherent manufactures a wide…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…power, a calibrated optical
power meter (detector head plus display console) is necessary.
Liquid (water) cooling is generally required for the detector head at
J-3 Series power levels. Make sure to provide adequate cooling for
the detector head.
Coherent manufactures a wide…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…power, a calibrated optical
power meter (detector head plus display console) is necessary.
Liquid (water) cooling is generally required for the detector head at
J-5 Series power levels. Make sure to provide adequate cooling for
the detector head.
Coherent manufactures a wide…

Microsoft Word - kW Thermopile Damage Threshold.doc

Microsoft Word - kW Thermopile Damage Threshold.doc

…Note Introduction A thermopile detector, commonly used for commercial laser power sensors, absorbs incident laser power and heats up, resulting in a temperature rise. This generates an electrical signal through the thermocouple arrays arranged around the detector. There are several failure modes…

COHR PowerMax-Pro DS 0917 3.pdf

COHR PowerMax-Pro DS 0917 3.pdf


30 mm
(1.18 in.)
21 mm
(0.83 in.)
51 mm
(2.0 in.)
109 mm
(4.3 in.)
76 mm
(3.0 in.)
Note: Detector surface is
9.8 mm (0.38 in.) below front
face of aperture plate
44 mm
(1.75 in.)
51 mm
(2.0 in.)
26 mm

PowerMaxPro 150BB 150HD drawing

PowerMaxPro 150BB 150HD drawing

…Hole 6 mm (0.25 in.) 30 mm (1.17 in.) 30 mm (1.18 in.) 30 mm (1.18 in.) 21 mm (0.83 in.) 51 mm (2.0 in.) 109 mm (4.3 in.) 76 mm (3.0 in.) Note: Detector surface is 9.8 mm (0.38 in.) below front face of aperture plate 44 mm (1.75 in.) 51 mm (2.0 in.) 26 mm (1.01 in.) 2X 6 mm (0.25 in.) 45 mm (1.77…

PowerMaxPro 150FBB 150FHD drawing

PowerMaxPro 150FBB 150FHD drawing

…in.) 104 mm (4.09 in.) 21 mm (0.83 in.) 23 mm (0.9 in.) 95 mm (3.75 in.) 109 mm (4.3 in.) 51 mm (2.0 in.) 51 mm (2.0 in.) 76 mm (3.0 in.) Note: Detector surface is 9.8 mm (0.38 in.) below front face of aperture plate 44 mm (1.75 in.) 30 mm (1.18 in.) 1/4-20 UNC Mounting Hole 10 mm (0.39 in.) 2X 6-32…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions