Ask a Question
Coherent

Search Results

1 - 12 of 93 Products for 'diamond e 400' Page 1 of 8 |
Related Categories: 1000w Co2 | J Series | Gem Laser | E400 | Diamond Series

diamond e 400

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 34 Mounting Laser System Components The integrated laser system has provisions for stress free kinematic mounting. This mounting includes mounting features (supplied with the laser) that facilitate laser replacement. Since the laser is precisely…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 30 13. Using the shackles provided, latch both eyebolts to the spreader bar as shown in Figure 19. Fully tighten the shackle pin. Figure 19. Attaching Eyebolts to Spreader Bar

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 26 6. Two people are required to carefully lift the wooden side panels up and over, exposing the system (Figure 12). 7. Cut the tape securing the top end of the user documents bag from the laser moisture seal bag (Figure 13). Figure 12. E-400…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 10 Freeze/Burst Protection The recommended coolant mixture does not provide freeze protection; therefore the coolant temperature must be maintained above the freezing point of water. Since lower temperatures may occur during shipment and…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 22 Facility Preparation Prepare the facility (installation site) as described in Table 1 on page 2. Unpacking and Inspection The E-400 Series laser system packaging has been designed for robust shipment. Upon receiving the system, inspect the…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 24 2. Remove the top cover (Figure 8). 3. Remove the water hose/filter kit, if provided (see Figure 9). Figure 8. Top Cover Removed Figure 9. Water Hoses and Filter Removal (if provided)

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 44 NOTICE! To avoid damaging the laser system, the coolant inlet and outlet must always be connected as specified. Any other connection method, e.g. connecting the laser head and RF power module in parallel with 2 separate inlets and outlets,…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 28 10. Install eyebolts to each end of the laser system (Figure 16). 11. Ensure both ratchet straps are clear of the laser system (Figure 17). Figure 16. Installation of Eyebolts Figure 17. Clear Straps from Laser System

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 46

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 46

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 46

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 30 13. Using the shackles provided, latch both eyebolts to the spreader bar as shown in Figure 19. Fully tighten the shackle pin. Figure 19. Attaching Eyebolts to Spreader Bar

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions