Ask a Question
Coherent

Search Results

13 - 24 of 205 Products for 'e 400 head' Page 2 of 18 |

e 400 head

00 E-400 Preinstall.book

00 E-400 Preinstall.book

…Standard gas fitting for purging the optics in the laser head. Nitrogen is not required for tube operation. Refer to "Optics Purge Gas" on page 4 for additional information on purging the laser head. Also note that the purge line on the laser head has a small filter. This filter protects the laser…

00 E-400 Preinstall.book

00 E-400 Preinstall.book

…Chapter Two: Laser Safety in the Operator's Manual. Utility Requirements The E-400 laser head and RF power supply require 48 VDC at 170 A (240 A peak for 1 msec). Cooling fluid is required for cooling the laser head and RF power supply. Electrical power, environment, and cooling fluid must meet the…

00 E-400 Preinstall.book

00 E-400 Preinstall.book

…Chapter Two: Laser Safety in the Operator's Manual. Utility Requirements The E-400 laser head and RF power supply require 48 VDC at 170 A (240 A peak for 1 msec). Cooling fluid is required for cooling the laser head and RF power supply. Electrical power, environment, and cooling fluid must meet the…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…optics purge gas line and perform a laser system purge (mandatory). 5. Connect the coolant lines and perform a leak check. 6. Connect the electrical cables. 7. Remove the output aperture cover and mount output accessories (couple beam delivery system to laser head). 8. Connect a laser controller.

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…optics purge gas line and perform a laser system purge (mandatory). 5. Connect the coolant lines and perform a leak check. 6. Connect the electrical cables. 7. Remove the output aperture cover and mount output accessories (couple beam delivery system to laser head). 8. Connect a laser controller.

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…RETURN SUPPLY SUPPLY RETURN RETURN Chiller Chiller Laser Head RF Power Module Laser Head Laser Head RF Power Module RF Power Module Flow loop shown is correct. Serial loop; Laser Head first. Flow direction is incorrect. Always connect to Laser Head first! Flow loop shown is incorrect. DO NOT make a…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…RETURN SUPPLY SUPPLY RETURN RETURN Chiller Chiller Laser Head RF Power Module Laser Head Laser Head RF Power Module RF Power Module Flow loop shown is correct. Serial loop; Laser Head first. Flow direction is incorrect. Always connect to Laser Head first! Flow loop shown is incorrect. DO NOT make a…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…gas fitting for purging the optics in the laser head. Nitrogen is not required for tube operation. Refer to "Laser System Purge Gas" on page 11 for additional information on purging the laser head. Also note that the purge line on the laser head has a small filter. This filter protects the laser…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…gas fitting for purging the optics in the laser head. Nitrogen is not required for tube operation. Refer to "Laser System Purge Gas" on page 11 for additional information on purging the laser head. Also note that the purge line on the laser head has a small filter. This filter protects the laser…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…(between laser head and RF power module) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas line between the laser head and RF power module Yes Tee 1 1/4 inch (6 mm) OD Tee for splitting the purge gas tubing at the laser head and RF…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…(between laser head and RF power module) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas line between the laser head and RF power module Yes Tee 1 1/4 inch (6 mm) OD Tee for splitting the purge gas tubing at the laser head and RF…

00 E-400 Series Preinstall.book

00 E-400 Series Preinstall.book

…(detector head plus display console) is necessary. Liquid (water) cooling is generally required for the detector head at E-400 Series power levels. Make sure to provide adequate cooling for the detector head. Coherent manufactures a wide range of power meters (display consoles and sensor heads).

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions