Ask a Question
Coherent
Search Results
Refine

Result Type

37 - 48 of 48 Products for 'e400 operators manual' Page 4 of 4 |

e400 operators manual

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 38 Set-up Purge Setup Purge is required in order to eliminate moisture from the system prior to use. This is required even though the system packaging is designed to ship the laser in a `dry condition'. Note that system purge is required…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 38 Set-up Purge Setup Purge is required in order to eliminate moisture from the system prior to use. This is required even though the system packaging is designed to ship the laser in a `dry condition'. Note that system purge is required…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…N2; required if using CDA Removes water vapor, oil, and particulates from compressed air; see Appendix E: Accessories and Options in the operator's manual No Purge Gas tubing (between laser head and RF power module) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…N2; required if using CDA Removes water vapor, oil, and particulates from compressed air; see Appendix E: Accessories and Options in the operator's manual No Purge Gas tubing (between laser head and RF power module) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…N2; required if using CDA Removes water vapor, oil, and particulates from compressed air; see Appendix E: Accessories and Options in the operator's manual No Purge Gas tubing (between laser head and RF power module) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 12 Laser System Purge Gas NOTICE! The use of specified purge gas will extend the life and reduce cost of ownership of the E-400 Series laser systems. The quality of the purge gas is extremely important factor for trouble free operation of the…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 12 Laser System Purge Gas NOTICE! The use of specified purge gas will extend the life and reduce cost of ownership of the E-400 Series laser systems. The quality of the purge gas is extremely important factor for trouble free operation of the…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 12 Laser System Purge Gas NOTICE! The use of specified purge gas will extend the life and reduce cost of ownership of the E-400 Series laser systems. The quality of the purge gas is extremely important factor for trouble free operation of the…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 8 Coolant Temperature At the laser head, the inlet temperature of the cooling fluid should always be above the dew point to prevent condensation from developing inside the laser head or RF power module. Coolant Filtering To prevent accumulation…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 8 Coolant Temperature At the laser head, the inlet temperature of the cooling fluid should always be above the dew point to prevent condensation from developing inside the laser head or RF power module. Coolant Filtering To prevent accumulation…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual 8 Coolant Temperature At the laser head, the inlet temperature of the cooling fluid should always be above the dew point to prevent condensation from developing inside the laser head or RF power module. Coolant Filtering To prevent accumulation…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…performance, ensure that the conditions remain within the tolerance limits listed in Table 1-2 "Utility Requirements" on page 1-10 (in the operator's manual) at all times. A closed-loop cooling system (chiller) should be used to obtain consistent and stable laser performance. The chiller must be…

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions