Search Results

25 - 36 of 38 Products for 'external trigger' Page 3 of 4 |

external trigger

Picosecond laser

Picosecond laser

…HV: no function
24 connecter to S-Control
25 no function, refer to the external AOM
26 BNC-connecter Trigger; The laser emits pulses according to the trigger sequence. In the
software "external" must be activated.
27 connecter for laser head interface cable (including ground…

LabMax Meters DS

LabMax Meters DS

…std. dev., dose, stability; trending, tuning, beam position
Computer Interface GPIB, USB and RS-232 USB and RS-232
Pulse Triggering Internal and external (selectable) -
Analog Output (VDC) 0 to 1, 2 or 4 (selectable)
Analog Output Update Rate Up to 1000 Hz for pyroelectric;

Mantis DS

Mantis DS

…Picker
Pulse Repetition Rate From ~9.5 kHz to 4.75 MHz variable by integer division of oscillator frequency.1
The unit also can be externally triggered at any repetition rate below 4 MHz or
operated single-shot.
Diffraction Efficiency2 (%)
TeO2 Cell >60
SiO2 Cell…

EnergyMax-USB-RS-Sensors-Guide FORMFIRST.pdf

EnergyMax-USB-RS-Sensors-Guide FORMFIRST.pdf

…compensation
curve for accurate use at wavelengths that differ from the
calibration wavelength
· External and Internal triggering available
· Units can share triggers to provide synchronized
measurements for applications such as ratiometry
Main Software Features

LaserCam-HR II User Manual

LaserCam-HR II User Manual


pulses.
Trigger Out Coherent suggests that an external pulse generator be used if the
laser under test does not supply a "sync-out" signal. Connect the
pulse generator to the Trigger In connector. A delayed trigger should
be applied to the Enable or Trigger input connector…

Revolution-Data-Sheet.pdf

Revolution-Data-Sheet.pdf


Umbilical Length 3 m (10 ft.)
Warm-up Time (minutes)(typical)
from standby mode <10
from cold start <30
1 Specifications apply at 1 kHz unless otherwise stated.
2 Operation below 500 Hz requires user supplied external TTL trigger.
3 Average of X & Y.

Microsoft Word - Understand Different Laser Beam  Rev 1 Final.doc

Microsoft Word - Understand Different Laser Beam Rev 1 Final.doc

…pulsed image data.
The signal normally comes from the
laser electronics external synch output.
Auto Triggering
Another triggering mode is auto
triggering which is similar to the
trigger used in oscilloscopes. Image
capture occurs when the intensity level
on…

LabMax Meters DS 8.qxd

LabMax Meters DS 8.qxd

…(mm) 0.1
Repetition Rate Error (%) <1
Maximum Repetition Rate (Hz) 10,000 sampling (1,000 Hz every pulse)
Pulse Triggering Internal and external (selectable)
Power Sampling Rate (Hz) 10
Uncertainty
Instrument ±1% of reading
System meter + sensor
Analog…

BeamView-USB Software Installation Guide

BeamView-USB Software Installation Guide

…The camera, trigger cable, camera mount, and
CD-ROM are shipped in a high-density plastic carrying case. This
specially-designed case protects all items during shipment.
Visually check all cartons for damage before unpacking. If there is
no visible external damage, remove…

COHR HighLightFL Compact MultiMode DS 0818.pdf

COHR HighLightFL Compact MultiMode DS 0818.pdf

…(CCU), Handheld (Touch screen)

* The recommended cooling capacity covers maximum power dissipation due to diode degradation and 100% laser power absorbed at an internal or external beam dump.

*
* An additional f ow rate of 500l/h is recomended for the use of an external power meter.

COHR HighLightFL Standard FFC DS 0818.pdf

COHR HighLightFL Standard FFC DS 0818.pdf

…(CCU), Handheld (Touch screen)

* The recommended cooling capacity covers maximum power dissipation due to diode degradation and 100% laser power absorbed at an internal or external beam dump.

*
* An additional flow rate of 500l/h is recomended for the use of an external power meter.

COHR HighLightFL Compact SingleMode DS 0818.pdf

COHR HighLightFL Compact SingleMode DS 0818.pdf

…(CCU), Handheld (Touch screen)

* The recommended cooling capacity covers maximum power dissipation due to diode degradation and 100% laser power absorbed at an internal or external beam dump.

*
* An additional flow rate of 500l/h is recomended for the use of an external power meter.

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions