Ask a Question
Coherent

Search Results

Refine
25 - 36 of 2565 Products for 'fiber laser' Page 3 of 214 |
Related Categories: Fl | Diamond Series | Mephisto Mopa 55w | Linewidth | Ultra

fiber laser

Picosecond laser

Picosecond laser

…taken into account: l Laser fibers cannot be disconnected (neither from the laser head nor from the power supply). l Connections between devices in the rack might be too short if the devices are taken out of the rack (or changed in its order). Some cables (e.g. laser fibers) cannot be extended.…

Picosecond laser

Picosecond laser

…into account: l Laser fibers cannot be disconnected (neither from the laser head nor from the power supply). l Connections between devices in the rack might be too short if the devices are taken out of the rack (or changed in its order). Some cables (e.g. HV cable, laser fibers) cannot be extended.…

Picosecond laser

Picosecond laser

…Rapid are located on the rear side of the power supply P90: Figure 5: Power supply P90, rear side 1 CPC connecter water in from laser head 2 Laser diodes with fiber coupler 3 Mains power cable (230 VAC, 50-60 Hz) 4 no function 5 Output connecter for emergency exit signal for a superior machine,…

Picosecond laser

Picosecond laser

…Rapid are located on the rear side of the power supply P90: Figure 5: Power supply P90, rear side 1 CPC connecter water in from laser head 2 Laser diodes with fiber coupler 3 Mains power cable (230 VAC, 50-60 Hz) 4 no function 5 Output connecter for emergency exit signal for a superior machine,…

Picosecond laser

Picosecond laser

…required and implemented into the interlock chain. l Guidance rail or tube for laser fibers (minimum bending radius 4 inches or 10 cm). The laser fibers need to be protected and covered against mechanical forces. l The laser beam path might need to be covered by an adequate housing, tubes, cabinet,…

Picosecond laser

Picosecond laser

…tube for laser fibers (minimum bending radius 10 cm or 4 inches). The laser fibers need to be protected and covered against mechanical forces. l The minimum bending radius of the chiller water hoses is: 13 cm or 5.1 inches). Protect the hoses against mechanical forces and crushing. l The laser beam…

Picosecond laser

Picosecond laser

…tube for laser fibers (minimum bending radius 10 cm or 4 inches). The laser fibers need to be protected and covered against mechanical forces. l The minimum bending radius of the chiller water hoses is: 13 cm or 5.1 inches). Protect the hoses against mechanical forces and crushing. l The laser beam…

Picosecond laser

Picosecond laser

…tube for laser fibers (minimum bending radius 10 cm or 4 inches). The laser fibers need to be protected and covered against mechanical forces. l The minimum bending radius of the chiller water hoses is: 13 cm or 5.1 inches). Protect the hoses against mechanical forces and crushing. l The laser beam…

Picosecond laser

Picosecond laser

…tube for laser fibers (minimum bending radius 10 cm or 4 inches). The laser fibers need to be protected and covered against mechanical forces. l The minimum bending radius of the chiller water hoses is: 13 cm or 5.1 inches). Protect the hoses against mechanical forces and crushing. l The laser beam…

Picosecond laser

Picosecond laser

…side of the laser head: Figure 9: Laser head Hyper Rapid-AOM, rear side 1 Chiller hose, cold water inlet from chiller 2 Chiller hose, outlet to power supply 3 High voltage power line for the pulse picker 4 S-Control 5 Timing signals 6 Interface laser 7 Umbilical with laser fibers 8 GATE: BNC plug…

Picosecond laser

Picosecond laser

…side of the laser head: Figure 9: Laser head Hyper Rapid-AOM, rear side 1 Chiller hose, cold water inlet from chiller 2 Chiller hose, outlet to power supply 3 High voltage power line for the pulse picker 4 S-Control 5 Timing signals 6 Interface laser 7 Umbilical with laser fibers 8 GATE: BNC plug…

Picosecond laser

Picosecond laser

…order and can deviate from the image. For a machine integration these information might need to be taken into account: l Laser fibers cannot be disconnected (neither from the laser head nor from the power supply). l Connections between devices in the rack might be too short if the devices are taken…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions