Search Results

37 - 48 of 50 Products for 'flat top' Page 4 of 5 |

flat top

COHR Genesis MX STM-Series DS 0517 3.pdf

COHR Genesis MX STM-Series DS 0517 3.pdf

…Dowel Pin (2X)
0.188 Dia. Thru (2X)
This surface must be flat within 0.001 in.
and have 32 µm finish or better within
TEC mounting areas.
Base Plate
Requirements
Front
View
Top View
Rear
View
Side View
Genesis MX STM-Series Datasheet…

Picosecond laser

Picosecond laser

…Also, make sure a power meter can
be placed into the optical beam path for diagnostic purposes.
Make sure you allow for access from the top and sides in order
to exchange the desiccant cartridges as well as remove the
laser head cover (only done by a certified technician, if

Genesis Taipan HD Series Datasheet 2016.pdf

Genesis Taipan HD Series Datasheet 2016.pdf


15.24 mm (0.6 in.)
8-32 UNC-2B X 0.50 Deep
(4X)
0.125 Dia. Dowel Pin (2X)
0.188 Dia. Thru (2X)
This surface must be flat within 0.001 in.
and have 32 µm finish or better within
TEC mounting areas.
Benelux +31 (30) 280 6060
China +86 (10) 8215 3600…

11-57-93 4- dimensional drawing

11-57-93 4- dimensional drawing

® ® 68.1 68.1 79.3 11.2 Protective Cap LDFP Adapter Rotational Mount 74.3 18.7 Image Plane 41.8 27.2 1/4-20 UNC 9.9 Top View Side View Bottom View Front View SCALE = 1:1.25 SIZE WT: DWG. NO. B SHEET 1 OF 1 REV DATE APPROVALS DFT: J. WILSON CHK: ENG: APR: MATERIAL: FINISH: NEXT ASSY PROPRIETARY…

COHR SapphireLPX DS 0418 2.pdf

COHR SapphireLPX DS 0418 2.pdf

…have
flatness <0.05 mm (0.002 in.)
Beam Waist at Exit Window
[3 mm (0.12 in.) inside from here]
[±200 mm (7.9 in.)]
4 Holes Ø4.0 mm (0.16 in.)
for Screws M3, UNC/UNF No.5&6,
1/8-40 BSW/BSF or BA No.4&5
Rear View
Front View
Top View

COHR SapphireSF DS 1017 1.pdf

COHR SapphireSF DS 1017 1.pdf

…Connection to Controller
(25pin SUB-D male)
DC Supply for Fan
(AMP-MODU-2pin-male)
Interfacing Part (Heatsink) should have
flatness <0.05 mm (0.002 in.)
Beam Waist at Exit Window
[3 mm (0.12 in.) inside from here]
[±200 mm (7.9 in.)]
4 Holes Ø4.0 mm…

CoherentLaserCladding March2014.pdf

CoherentLaserCladding March2014.pdf

…heat resistance) of a part or to re-surface a component that has become worn through use. Cladding involves the creation of a new surface layer on top of a base material. This is distinct from surface hardening, which simply entails changing the properties of the substrate itself in a thin surface…

Properties-of-Structured-Light-Application-Note.pdf

Properties-of-Structured-Light-Application-Note.pdf

…of the
measurements.
ALG (Aspheric Line Generator)
Refractive aspheric line generators are a technology that generates a uniform top
hat profile by combining the function of a roof prism and an aspheric cylinder.
The prism acts on the incoming beam to refract the light…

Industrial Photonics - January 2014

Industrial Photonics - January 2014

…and this diversification and specialization shows no signs of abating. Laser cladding Cladding involves the creation of a new surface layer on top of a base material. It is a widely used process for improving the surface and near-surface properties (e.g., wear, corrosion or heat resistance)…

COHR SapphireLP DS 1017 1.pdf

COHR SapphireLP DS 1017 1.pdf

…Connection to Controller
(25pin SUB-D male)
DC Supply for Fan
(AMP-MODU-2pin-male)
Interfacing Part (Heatsink) should have
flatness <0.05 mm (0.002 in.)
Beam Waist at Exit Window
[3 mm (0.12 in.) inside from here]
[±200 mm (7.9 in.)]
4 Holes Ø4.0 mm…

IndustrialUltrafast Whitepaper.pdf

IndustrialUltrafast Whitepaper.pdf

…quality level is virtually impossible to
achieve using traditional, mechanical machining
methods.
Figure 4: The EWAG Laser Line Ultra (top) is a system for
fabricating diamond tools. The photos compare a tool edge
prepared using traditional diamond grinding with one

Excimer LLO 2014.pdf

Excimer LLO 2014.pdf

…lasers enables a large processing footprint and the high-throughput rates needed in mass manufacturing. Thin-film transistor structures fabricated on top of polymer layers spun on glass panels must be delaminated to create thin, lightweight, and rugged flexible-display backplanes. Low-thermal-budget…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions