Search Results

37 - 48 of 49 Products for 'glass drilling' Page 4 of 5 |

glass drilling

COHR HyperRapid100 355-SW DS 0716 6.pdf

COHR HyperRapid100 355-SW DS 0716 6.pdf

…capability for increased ablation rate · High throughput at significantly reduced TCO HyperRapid 100 355-SW Applications: · Cutting and drilling of strengthened glass, sapphire, ceramics and other tough materials, also composites · Micromachining and structuring of large surfaces with line focusing…

Information Display Magazine September/October 2017, Vol. 33, No. 5 issue

Information Display Magazine September/October 2017, Vol. 33, No. 5 issue

…it takes about 1 second to
drill a 1-mm diameter hole in 3-mm-thick
soda lime glass. The cutting speed for free
contours is in the single-digit mm-per-second
range. Other drawbacks are that this method
cannot process strengthened glass, and the
edges typically show…

32311a coverSinglesRR.indd

32311a coverSinglesRR.indd

…could only be produced on expensive special glass at high temperatures. However, excimer-based
processes, such as excimer laser annealing (``ELA'') have allowed high-volume production of
low-temperature polysilicon (``LTPS'') on conventional glass substrates. Our excimer lasers provide a…

Coherent

Coherent

…could only be produced on expensive special glass at high temperatures. However, excimer-based
processes, such as excimer laser annealing (``ELA'') have allowed high-volume production of
low-temperature polysilicon (``LTPS'') on conventional glass substrates. Our excimer lasers provide an…

CMM 8.2.indd

CMM 8.2.indd

…etching, sand blasting,
ultrasound drilling or laser ablation.
To investigate the potential for using lasers
for this application, the Coherent applications
laboratory laser drilled a large number of
tightly spaced holes into a glass wafer.
Specifically, these were 25…

RAPID-FX-Data-Sheet-06-17-15.pdf

RAPID-FX-Data-Sheet-06-17-15.pdf

…68 cm x 26 cm x 29 cm contains all electronics; external chiller required RAPID FX Applications: · Percussion drilling of small apertures for injector nozzles in metal · High precision machining of medical parts · Low-k scribing · Micromachining of glass and sapphire parts www.Coherent.com/RAPID_FX

Industrial Photonics - July 2014

Industrial Photonics - July 2014

…processing is the more frequent use
of multikilowatt fiber lasers, specifically in automotivewelding applications, aerospace and aviation drilling applications," said John McCauley, product specialist in the
laser measurement group at Ophir-Spiricon.
Among other things, Ophir-Spiricon…

EU LTJ Ultrashort Pulses Improving the Process.pdf

EU LTJ Ultrashort Pulses Improving the Process.pdf

…purposes. Glass cutting: quantifying key process results To understand how this works in practice, consider a recently qualified application in which Coherent femtosecond lasers were utilized to cut thin (<1 mm) sheet glass for use in displays. This producer had been cutting glass mechanically,…

Improving and Quantifying the Process Window

Improving and Quantifying the Process Window

…purposes. Glass cutting: quantifying key process results To understand how this works in practice, consider a recently qualified application in which Coherent femtosecond lasers were utilized to cut thin (< 1 mm) sheet glass for use in displays. This producer had been cutting glass mechanically,…

IndustrialUltrafast Whitepaper.pdf

IndustrialUltrafast Whitepaper.pdf

…manufacture and many other industries, there is an increasing trend towards higher precision processing. Specifically, this means cutting, drilling and marking of parts with smaller feature sizes and greater accuracy, and with reduced effect on surrounding material. In the past, most precision…

34706a cover.indd

34706a cover.indd

…only be produced on expensive special glass at high temperatures.
However, excimer-based processes, such as excimer laser annealing (``ELA'') have allowed high-volume
production of low-temperature polysilicon (``LTPS'') on conventional glass substrates as well as flexible
displays…

Industrial Laser Solutions - January / February 2014

Industrial Laser Solutions - January / February 2014

…reinforcement, which provides loadbearing strength and rigidity, is carbon fber, usually woven like a fabric. Other fbers such as Kevlar, aluminum, or glass are also often added. The matrix, which surrounds the reinforcement and binds it together, is most commonly epoxy or some other polymer resin.…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions