Search Results

61 - 72 of 77 Products for 'green pulsed laser' Page 6 of 7 |

green pulsed laser

Chameleon-Peak-Power-White-Paper.pdf

Chameleon-Peak-Power-White-Paper.pdf

…Pre-Compensation of
15 Femtosecond Optical Pulses for HighNumerical-Aperture Objectives, Journal of
Microscopy, vol 191, 2 (1998).
11. R. Szipocs, et al., Chirped Multilayer Coatings for
Broad-Band Dispersion Control in Femtosecond
Lasers, Optics Letters, vol 19, 3 (1994).…

WP ChameleonPeakPower Final.pdf

WP ChameleonPeakPower Final.pdf

…Pre-Compensation of
15 Femtosecond Optical Pulses for HighNumerical-Aperture Objectives, Journal of
Microscopy, vol 191, 2 (1998).
11. R. Szipocs, et al., Chirped Multilayer Coatings for
Broad-Band Dispersion Control in Femtosecond
Lasers, Optics Letters, vol 19, 3 (1994).…

SurfaceCatalystStructure AstrellaProfXiong2D Case Study FINAL.pdf

SurfaceCatalystStructure AstrellaProfXiong2D Case Study FINAL.pdf

…demands on laser stability. During this
period it is critical that the amplifier output be stable and without drifts in beam pointing, beam
quality, pulse energy, etc. The stability of Astrella means we can do these long data runs while
remotely controlling the laser from an office…

Mira brochure

Mira brochure

…The result
is the efficient generation of short pulses in
either the femtosecond or picosecond regime.
Superior pump lasers.
At the core of the Mira system is the Verdi CW
diode-pumped laser. This 532 nm green laser
offers several compelling advantages: stable,

Information Display Magazine September/October 2017, Vol. 33, No. 5 issue

Information Display Magazine September/October 2017, Vol. 33, No. 5 issue

lasers with pulse widths in the nanosecond range, or ultra-short-pulse (USP) lasers
with pulse widths in the picosecond, or even
femtosecond, range.
There are several different variations on the
way laser ablation is used to cut glass, but in
all of them, each laser pulse

Chameleon Reliability Antarctia Final WP.pdf

Chameleon Reliability Antarctia Final WP.pdf

…where the lasers are operated by personnel with limited laser experience working on live animals, like in a neuroscience laboratory. Until 7-8 years ago, the majority of Ti:S ultrafast lasers required a separate green pump laser that the user had to place close to the ultrafast laser and feed into…

Bio Photonics - April 2015

Bio Photonics - April 2015

…wavelengths - one
from the Ti:S laser and one from an OPO
pumped by this laser, all under pushbutton integrated computer control. Dr.
Emmanuel Beaurepaire of CNRS et al
have recently shown that independent
tunability of two synchronous pulses can
excite all the brainbow…

Photonics Spectra - March 2018

Photonics Spectra - March 2018

…responsible for lasers and
their applications that address scientific research; email: marco.arrigoni@coherent.com.
Mike LaHa is the product manager for the
Monaco laser at Coherent Inc. He has over 25
years of experience in applications and marketing within the laser industry;…

Industrial Photonics - July 2018

Industrial Photonics - July 2018

lasers emit at
around 1064 nm. But, because of the high beam quality
of fiber lasers, the light can be focused down to a small
spot size. With enough power, very precise, high-quality
welds are possible, Mendes said. This is the case both for
CW lasers and those with pulsed

Photonics Spectra - September 2017

Photonics Spectra - September 2017

…directly obtain
the emission frequency information. Three
of the four laser pulses are passed through
a pair of glass wedges so that they can independently vary their phase relative to the
fourth pulse, which is used for heterodyning detection. "This gives us three time

Photonics Spectra - September 2016

Photonics Spectra - September 2016


was the 308-nm excimer laser for selective low-temperature polysilicon recrystallization. The excimer laser process to
Adapting Laser Lift-Off Technique for Flexible Displays
Excimer lasers optimized for high-energy
pulses have applications beyond annealing…

Bio Optics World - May/June 2014

Bio Optics World - May/June 2014

lasers based on colliding pulse
modelocked (CPM) dye lasers consisted of
a large optical table with myriad individual optics and required continuous tweaking and re-optimization by a highly skilled
laser expert. Then came Ti:sapphire lasers,
pumped first by ion lasers, then by…

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions