Search Results

Refine
37 - 48 of 80 Products for 'heat sink' Page 4 of 7 |

heat sink

CUBE family DSrevD

CUBE family DSrevD


Threads for
Accessory Mounting
2x M4 8
2 x 8-32 8.33 mm (0.33 in.)
OBIS Heat Sink
Part #1193289
Fan included
OBISTM Accessories
OBIS Remotes, Heat Sink, Power Supply and Accessories
Top View
Side View
Front View Rear View
OBIS Single…

COHR SapphireFP DS 1017 1.pdf

COHR SapphireFP DS 1017 1.pdf


Heat Sink (optional) 200 x 80 x 50 mm/7.9 x 3.2 x 2.0 in.
DC Power Supply (optional) 171 x 104 x 55 mm/6.7 x 4.1 x 2.2 in.
Cable Laser Head to Controller 2m/6.56 ft. and options
Weights
Laser Head7 0.35 kg/0.77 lbs.
Controller 0.25 kg/0.55 lbs.
Heat Sink (optional)…

COHR SapphireLP DS 1017 1.pdf

COHR SapphireLP DS 1017 1.pdf

…Dimensions (L x W x H)
Laser Head 125 x 70 x 34 mm (4.9 x 2.8 x 1.3 in.)
Controller
117.8 x 76.2 x 30 mm (4.6 x 3.0 x 1.2 in.)
Heat Sink (optional) 200 x 80 x 50 mm (7.9 x 3.2 x 2 in.)
DC Power Supply (optional) 171 x 104 x 55 mm (6.7 x 4.1 x 2.2 in.)
Cable -- Laser…

COHR SapphireLPX DS 0418 2.pdf

COHR SapphireLPX DS 0418 2.pdf

…Non-Operating Condition
0 to 95, non-condensing
0 to 100, non-condensing
Dimensions (L x W x H)
Laser Head
Controller
Heat Sink (optional)
DC Power Supply (optional)
Cable -- Laser Head to Controller
125 x 70 x 34 mm (4.9 x 2.8 x 1.3 in.)
117.8 x…

COHR SapphireSF DS 1017 1.pdf

COHR SapphireSF DS 1017 1.pdf

…Dimensions (L x W x H)
Laser Head 125 x 70 x 34 mm (4.9 x 2.8 x 1.3 in.)
Controller
117.8 x 76.2 x 43.2 mm (4.6 x 3.0 x 1.7 in.)
Heat Sink (optional) 200 x 80 x 50 mm (7.9 x 3.2 x 2 in.)
DC Power Supply (optional) 172 x 105 x 55 mm (6.8 x 4.1 x 2.2 in.)
Cable -- Laser…

PowerMax-Pro-White-Paper-Novel-Laser-Power-Sensor-Improves-Process-Control FORMFIRST.pdf

PowerMax-Pro-White-Paper-Novel-Laser-Power-Sensor-Improves-Process-Control FORMFIRST.pdf

…sensitivity. The
heat then flows across the width of the thermopile disk
to the heat sink which is held at a near constant
ambient temperature by either air- or water-cooling.
The temperature difference between the absorber and
heat sink is converted into an electrical…

CCP 870-990 DS

CCP 870-990 DS

…Temperature (°C) 25
Recommended Operating Temperature Range (°C) 15 to 35
Storage Temperature Range (°C) -40 to +60
Recommended Heat Sink Capacity (W) 120
870-890 nm CCP
Conduction-Cooled Single Bar Package
Typical 870-890 nm P-I Plots
0
10
20
30…

Verdi preinstall.book

Verdi preinstall.book

…5 to 95% (non condensing)
Altitude Sea level to 10,000 feet
Table 1-3. Laser System Dimensions
POWER SUPPLY LASER HEAD UMBILICAL HEAT SINK
Length 45.2 cm (17.8 in.) 46.43 cm (18.28 in.) 3 meters (10 ft.) 38.81 cm (15.28 in.)
Width 43.4 cm (17.1 in.) 10.87 cm (4.28 in.) --…

SingleEmitters-780-830nm-Data-Sheet.pdf

SingleEmitters-780-830nm-Data-Sheet.pdf

…current transients greater than 25 µA and/or reverse voltages >3V can destroy the unit.
Unit requires an adequate heat sink. Failure to supply an adequate heat sink will destroy the unit.
A dry environment should be provided when storing or operating a device with an open diode laser…

Layout 1

Layout 1

…PowerMax-Pro sensor. The short heat flow path results in fast measurement
speeds.
Thin film thermoelectric sensor
with parallel heat flow
50 s response time
Heat sink
Absorbing
material
Incident
laser
light
Heat
flow
Thin (microns)…

Photonics Spectra - July 2014

Photonics Spectra - July 2014

…enhance sensitivity. The heat then
flows across the width of the thermopile
disk to the heat sink, which is held at a
near-constant ambient temperature by either air or water cooling. The temperature
difference between the absorber and heat
sink is converted into an…

WP-Meterless-Laser-Power-Energy-Measurement-Simplifies-Embedding.pdf

WP-Meterless-Laser-Power-Energy-Measurement-Simplifies-Embedding.pdf

…incident laser radiation and convert it into heat. This
heat ultimately flows to a heat sink that is held at a near constant ambient
temperature by either air or water-cooling. The temperature difference between the
absorber and heat sink is converted into an electrical signal by an…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions