Ask a Question
Coherent

Search Results

Refine
1 - 12 of 19 Products for 'hollow' Page 1 of 2 |

hollow

Highlights No. 58 V5for PDF.QXP

Highlights No. 58 V5for PDF.QXP

…light that closely matched that of the hollow cathode lamp. The second problem was solved by using the optical system shown in Fig. 1. After exiting the scattering plate, light from the laser passed through a small aperture and was directed toward the hollow cathode lamp by a beam splitter (uncoated…

EOdec07 pp22-25 medical

EOdec07 pp22-25 medical

…electro optics 40th anniversary issue DesignsforlifeWilliam Payne probes the market for photonics in medicine The Bone Trephine shows what the laser as a tool can do. For example, variable cutting angles and minimal radii for cut-outs of tubes and hollow parts. Image courtesy of Trumpf.

00 Radius.book

00 Radius.book

…with the factory-set collimated beam. · The safety shutter will not function with the Adjustable Focus Tool inserted. The adjustment tool has a hollow bore so the beam can be adjusted while the laser is in use. Take all appropriate laser safety precautions. Focused laser beams can present additional…

Draft

Draft

A built-in hollow-cathode lamp routinely calibrates the wavelength of the monitoring scale. The hollow cathode lamp gives reference to the atomic transition of iron at 193.4538 nm. For the NovaLine A4003 laser the wavelength and bandwidth monitor system have been redesigned. The finesse of the…

Highlights No. 62 FINAL.QXP

Highlights No. 62 FINAL.QXP

…sections this dual side illumination was found to be mandatory to observe the area near the spark plug (see especially Fig. 5). The main part of the hollow cone spray in Fig. 3 is well positioned to distribute fuel to form the desired homogeneous mixture. The open inlet valves, however, cut off a…

http://www.optoiq.com/index/photonics-technologies-applications

http://www.optoiq.com/index/photonics-technologies-applications

…low M2 value in a single-pass setup, the design combines optical simplicity and efficiency with the ideal beam characteristics for focusing into hollow fiber cores or pumping multiple high-energy OPAs, and eliminates the need for complex cryogenic cooling (see Fig. 4). of the regenerative amplifier…

Highlights No. 62 FINAL.QXP

Highlights No. 62 FINAL.QXP

…for Internal Combustion Engine Development" Journal of electronic imaging / July 2001/ Vol. 10(3) p 588 - 592. Fig. 4: PLIF image sequence shows hollow cone spray penetration during intake stroke. Free propagation of frontal spray part, but significant interaction with open inlet valve of rear spray…

70410-186e.indd

70410-186e.indd

…is electroplated. Lasers are also being used by some manufacturerstocuttherawsiliconitself. For example, RWE Schott Solar pulls its silicon in a hollow octagonal shape, each side of which becomes a wafer strip. 1064nmlaserscuteachvertexoftheoctagonathighspeed.Conversely,Evergreen Solar pulls its…

Highlights No. 61 | 24.10.QXP

Highlights No. 61 | 24.10.QXP

…shown in figures 1,3,4, and 5, have been obtained with the commercial laboratory EUV source built by AIXUV GmbH. This EUV source is based on the Hollow Cathode Triggered (HCT) pinch design and operates at a 50 Hz repetition rate, emitting roughly 500 mW/sr of total EUV power between 8 nm and 20 nm.…

SuperiorPointingStabilitySimplifiesMPEImaging final 03 19 10.pdf

SuperiorPointingStabilitySimplifiesMPEImaging final 03 19 10.pdf

…one plane only. Using two of these prisms allows any slight walk-off in both x and y axes to be avoided, yet without specifying trihedral prisms or hollow retroreflectors optics with tolerances that would be very difficult (and prohibitively expensive) to consistently produce. Nonetheless even using…

SuperiorPointingStabilitySimplifiesMPEImaging final 03 19 10.pdf

SuperiorPointingStabilitySimplifiesMPEImaging final 03 19 10.pdf

…one plane only. Using two of these prisms allows any slight walk-off in both x and y axes to be avoided, yet without specifying trihedral prisms or hollow retroreflectors optics with tolerances that would be very difficult (and prohibitively expensive) to consistently produce. Nonetheless even using…

Superior-Pointing-Stability-Simplifies-MPE-Imaging.pdf

Superior-Pointing-Stability-Simplifies-MPE-Imaging.pdf

…one plane only. Using two of these prisms allows any slight walk-off in both x and y axes to be avoided, yet without specifying trihedral prisms or hollow retroreflectors optics with tolerances that would be very difficult (and prohibitively expensive) to consistently produce. Nonetheless even using…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions