Ask a Question
Coherent

Search Results

Refine
13 - 24 of 304 Products for 'interlock fault' Page 2 of 26 |

interlock fault

Avia preinstall.book

Avia preinstall.book

…if no active faults. Fault codes: 1=Emission Indicator Fault, 2=External Interlock Fault, 3=PS Cover Interlock Fault, 4=SHG Temp. Fault, 5=N/A, 6=Laser Rods Temp. Fault, 7=FHG Temp. Fault, 8=Diode 1 Temp. Fault, 9=Diode 2 Temp. Fault, 10=Baseplate Temp. Fault, 11=Heatsink 1 Temp. Fault, 12=Heatsink…

Avia preinstall.book

Avia preinstall.book

…if no active faults. Fault codes: 1=Emission Indicator Fault, 2=External Interlock Fault, 3=PS Cover Interlock Fault, 4=SHG Temp. Fault, 5=N/A, 6=Laser Rods Temp. Fault, 7=FHG Temp. Fault, 8=Diode 1 Temp. Fault, 9=Diode 2 Temp. Fault, 10=Baseplate Temp. Fault, 11=Heatsink 1 Temp. Fault, 12=Heatsink…

Avia preinstall.book

Avia preinstall.book

…if no active faults. Fault codes: 1=Emission Indicator Fault, 2=External Interlock Fault, 3=PS Cover Interlock Fault, 4=SHG Temp. Fault, 5=N/A, 6=Laser Rods Temp. Fault, 7=FHG Temp. Fault, 8=Diode 1 Temp. Fault, 9=Diode 2 Temp. Fault, 10=Baseplate Temp. Fault, 11=Heatsink 1 Temp. Fault, 12=Heatsink…

Avia preinstall.book

Avia preinstall.book

…if no active faults. Fault codes: 1=Emission Indicator Fault, 2=External Interlock Fault, 3=PS Cover Interlock Fault, 4=SHG Temp. Fault, 5=N/A, 6=Laser Rods Temp. Fault, 7=THG Temp. Fault, 8=Diode 1 Temp. Fault, 9=Diode 2 Temp. Fault, 10=Baseplate Temp. Fault, 11=Heatsink 1 Temp. Fault, 12=Heatsink…

Avia preinstall.book

Avia preinstall.book

…if no active faults. Fault codes: 1=Emission Indicator Fault, 2=External Interlock Fault, 3=PS Cover Interlock Fault, 4=SHG Temp. Fault, 5=N/A, 6=Laser Rods Temp. Fault, 7=THG Temp. Fault, 8=Diode 1 Temp. Fault, 9=Diode 2 Temp. Fault, 10=Baseplate Temp. Fault, 11=Heatsink 1 Temp. Fault, 12=Heatsink…

Avia preinstall.book

Avia preinstall.book

…if no active faults. Fault codes: 1=Emission Indicator Fault, 2=External Interlock Fault, 3=PS Cover Interlock Fault, 4=SHG Temp. Fault, 5=N/A, 6=Laser Rods Temp. Fault, 7=THG Temp. Fault, 8=Diode 1 Temp. Fault, 9=Diode 2 Temp. Fault, 10=Baseplate Temp. Fault, 11=Heatsink 1 Temp. Fault, 12=Heatsink…

00 Cube.book

00 Cube.book

…Checklist 1: Interlock Fault If an interlock fault is suspected, execute the following steps. [ ] Cycle DC power OFF/ON. [ ] Verify supply voltage is between 4.8 VDC to 6.5 VDC. [ ] Connect a computer and send the "?LCK" or "?INT" query. If a value of 0 is returned, check all interlock connections.…

Book.book

Book.book

…Checklist 1: Interlock Fault If an interlock fault is suspected, execute the following steps. [ ] Cycle DC power OFF/ON. [ ] Verify the supply voltage is between 4.8 and 6.5 VDC. [ ] Connect a computer and send the "?LCK" or "?INT" query. If a value of 0 is returned, check all interlock connections.…

00 Cube FP .book

00 Cube FP .book

Troubleshooting 8 - 3 Checklist 1: Interlock Fault If an interlock fault is suspected, execute the following steps. [ ] Cycle DC power OFF/ON. [ ] Ensure DE-15 connector is properly secured with locking screws. [ ] Verify supply voltage is between 4.8 VDC to 6.5 VDC. [ ] Connect a computer and send…

00 Cube FP .book

00 Cube FP .book

…to the associated Troubleshooting checklist located in this section. Table 8-1. Troubleshooting Procedures PROBLEM TROUBLESHOOTING REFERENCE Interlock Fault Checklist 1 No Laser Emission at Start-up Checklist 2 System Shuts Down (RS-232 Control) Checklist 3a System Shuts Down (Analog Control and…

Book.book

Book.book

…temperature and the measured diode temperature is greater than 5ºC Improve heat sink to reduce the diode temperature 32 Interlock Fault Interlock is open Close the Interlock connection 64 I2C Error Processor-to-hardware communication error Reboot the laser system--contact Coherent Technical Support…

00 Cube FP .book

00 Cube FP .book

…diode set temperature and measured diode temperature is greater than 5ºC. Improve heat sink to reduce diode temperature. 32 Interlock Fault Interlock Open Close Interlock Connection 64 I2C Error Processor to Hardware communication error. Reboot the laser system. If the problem persists, contact…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions