Search Results

1 - 12 of 20 Products for 'interlock fault' Page 1 of 2 |

interlock fault

Verdi preinstall.book

Verdi preinstall.book


External
Interlock
The system will not operate with the interlock open. An interlock
connector is located on the power supply rear panel. The interlock
status is monitored by the CPU. If the interlock is open, the message,
"External Interlock Fault" will be displayed on…

Avia preinstall.book

Avia preinstall.book

…no active faults.
Fault codes:
1=Emission Indicator Fault,
2=External Interlock Fault,
3=PS Cover Interlock Fault,
4=SHG Temp. Fault,
5=N/A,
6=Laser Rods Temp. Fault,
7=FHG Temp. Fault,
8=Diode 1 Temp. Fault,
9=Diode 2 Temp. Fault,
10=Baseplate…

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

…Laser Fault
· Power On
The following table lists all the possible states of the controller
Status LEDs.
For information on the laser Status LED, refer to Table 2-2 on
page 2-3.
Interlock Jumper This is a mechanical-style jumper for
CDRH interlock. The interlock has…

Book.book

Book.book

Interlock Fault
If an interlock fault is suspected, execute the following steps.
[ ] Cycle DC power OFF/ON.
[ ] Verify the supply voltage is between 4.8 and 6.5 VDC.
[ ] Connect a computer and send the "?LCK" or "?INT" query.
If a value of 0 is returned, check all interlock

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…4.2 except for the
output beam, which is Class 4.
Safety Interlocks The system incorporates multiple safety interlocks which activate
when the top cover(s) of the laser head is removed. An interlock
fault initiation will terminate the pump laser by activating a shutter

Libra PreInstallation.book

Libra PreInstallation.book

…60825-1/IEC 60825-1, clause 4.8].
Manual Reset
Mechanism
Following an interlock fault or unexpected loss of electrical power,
laser operation requires manual clearing of the fault condition(s)
[CFR 1040.10(f)(10)/EN 60825-1/IEC 60825-1, clause 4.11].
Use of…

00 Legend Elite Preinstallation.book

00 Legend Elite Preinstallation.book

…4.2 except for the
output beam, which is Class 4.
Safety Interlocks The system incorporates multiple safety interlocks which activate
when the top cover(s) of the laser head is removed. An interlock
fault initiation will terminate the pump laser by activating a shutter

Vitara Preinstall.book

Vitara Preinstall.book

…the operator to laser emission
[CFR 1040.10(f)(8)/EN 60825-1/IEC 60825-1, clause 4.9].
Manual Reset
Mechanism
Following an interlock fault or unexpected loss of electrical power,
laser operation is resumed keying the power supply off and then on.
[CFR 1040.10(f)(10)/EN…

00 E-250 Pre.book

00 E-250 Pre.book

…4-17
System Interlock ...................................................................................................... 4-17
Shutter Control and Status ....................................................................................... 4-17
Over Temperature Fault

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…4-18
System Interlock ...................................................................................................... 4-18
Shutter Control and Status ....................................................................................... 4-18
Over Temperature Fault

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…4-18
System Interlock ...................................................................................................... 4-18
Shutter Control and Status ....................................................................................... 4-18
Over Temperature Fault

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

…Screen
The Status Screen shows the details of the laser from
serial number to operating hours. A separate Fault
Screen also shows any faults from an interlock fault to
over-temperature.
The Control Box
To comply with the CDRH safety requirements for a
Class IIIb…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions