Ask a Question
Coherent

Search Results

Refine

Result Type

13 - 24 of 105 Products for 'j2 manual' Page 2 of 9 |

j2 manual

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 4 - 2 Figure 4-1. J-2 Series Laser Electrical Interfaces Table 4-1. J-2 Series Laser Electrical Interfaces INTERFACE OR INDICATOR DESCRIPTION OPERATOR'S MANUAL SECTION Real-time Control and Status I/O DB-25 connector (male) Similar to existing K…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual x Preface This manual provides preinstallation instructions for DIAMONDTM J-2 Series lasers - OEM version. The laser safety section must be reviewed thoroughly prior to operating the DIAMOND J-2 Series laser system. NOTICE! Read the DIAMOND J-2

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 3 - 24 Option Two: Eyebolt Method 1. Follow step 1 through step 3 in the forklift method. 2. Locate and remove user documents and lifting eyebolts from the accessories bag (Figure 3-10). 3. Insert the supplied eyebolts into the holes as shown in…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 3 - 30 2. Securely connect appropriate slings or chains to the eyebolts and a user-supplied spreader bar. Chains/slings must be vertical when under load. See Figure 3-15. 3. Carefully lift the laser system while preventing the free end from moving…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 4 - 16 Figure 4-10. RF Amplifier Output Signals - VSWR Fault for a 60% Duty Cycle Limit Example Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 3 - 28 NOTICE! Customers mounting the laser in a 'non-horizontal' feet down configuration are responsible for properly supporting the laser during installation (and de-installation). Great care must be taken that the laser (35 kg or 77 lbs.) plus…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 3 - 34 + 48 VDC Cable Connection The + 48 VDC cable from the DC power supply is to be connected to the + 48 VDC marked connector on the rear panel. This is a special filtered connector that passes DC current but blocks RF emission. As illustrated…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 4 - 12 Monitoring Circuit Example An example of a monitoring circuit that can be connected to the output of the Real Time I/O interface circuit is indicated in Figure 4-7. Figure 4-7. Typical Monitoring Circuit Example Status Monitor (Real Time…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 2 - 10 Laser System Specifications The J-2 Series laser system's physical characteristics and utility requirements common to all J-2 Series models are given in Table 2-1 and Table 2-2. Laser performance specifications for a specific J-2 Series…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 2 - 4 Laser System Components The DIAMOND J-2 Series laser housing contains the laser resonator in a vacuum sealed compartment, RF power module along with the RF matching network in a second compartment, and the beam conditioning optics and…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 3 - 12 Guidelines for Use of Compressed Air for Purge If nitrogen is not available, the alternative is clean, dry, oil-free compressed air. Compressed air is available in many facilities but typically is contaminated with water and oil vapors. The…

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-2 Series OEM Lasers Preinstallation Manual 1 - 2 WARNING! Direct eye contact with the output beam from the laser will cause serious eye damage and may cause blindness. All personnel in the same room as the laser or anyone who may be exposed to the laser beam should be informed that a laser…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions