Ask a Question
Coherent
Search Results
25 - 36 of 820 Products for 'labmax to manual' Page 3 of 69 |

labmax to manual

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

…Set the mode to Joules by using either the UNITS soft key on the meter, or the CONFigure:MEASure host command. 2. Query the host for measurement data by using the FETCh:NRECords query. (For detailed information, refer to "Data Query" in the Host Interface section of the user manual.) The type of…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 15 of 16 Once the calculation has been completed, the new Joules value is displayed, the CALCULATING indicator is replaced with READY, and the plot stops (see the following figure). At this point, the meter is ready to receive another pulse. Soft Keys There are three…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 15 of 16 Once the calculation has been completed, the new Joules value is displayed, the CALCULATING indicator is replaced with READY, and the plot stops (see the following figure). At this point, the meter is ready to receive another pulse. Soft Keys There are three…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 15 of 16 Once the calculation has been completed, the new Joules value is displayed, the CALCULATING indicator is replaced with READY, and the plot stops (see the following figure). At this point, the meter is ready to receive another pulse. Soft Keys There are three…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 14 of 16 Thermopile Sensors, Long Pulse Joules Connecting a thermopile sensor to the meter and switching to Joules mode displays the screen shown below. This mode measures the energy of single pulses between 1 millisecond and 10 seconds in length, and with energies…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 14 of 16 Thermopile Sensors, Long Pulse Joules Connecting a thermopile sensor to the meter and switching to Joules mode displays the screen shown below. This mode measures the energy of single pulses between 1 millisecond and 10 seconds in length, and with energies…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 14 of 16 Thermopile Sensors, Long Pulse Joules Connecting a thermopile sensor to the meter and switching to Joules mode displays the screen shown below. This mode measures the energy of single pulses between 1 millisecond and 10 seconds in length, and with energies…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 9 of 16 HRESULT SendCommandOrQuer ([in] SHORT iMeterIndex, [in] BSTR iCommandOrQuery, [out,retval] SHORT
* oResult) Inputs: iMeterIndex--valid parameter values depend on the communication mode. For more information, refer to "Detailed Reference" on page 4.…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 9 of 16 HRESULT SendCommandOrQuer ([in] SHORT iMeterIndex, [in] BSTR iCommandOrQuery, [out,retval] SHORT
* oResult) Inputs: iMeterIndex--valid parameter values depend on the communication mode. For more information, refer to "Detailed Reference" on page 4.…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 9 of 16 HRESULT SendCommandOrQuer ([in] SHORT iMeterIndex, [in] BSTR iCommandOrQuery, [out,retval] SHORT
* oResult) Inputs: iMeterIndex--valid parameter values depend on the communication mode. For more information, refer to "Detailed Reference" on page 4.…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 3 of 16 Installation The ActiveX control and low-level DDL are automatically installed--along with the LabMax PC Applications software--when you run the CD that is supplied with the meter. LabMax Low Level Control Overview The LabMax Low Level Control…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

LabMax User Manual Addendum Page 3 of 16 Installation The ActiveX control and low-level DDL are automatically installed--along with the LabMax PC Applications software--when you run the CD that is supplied with the meter. LabMax Low Level Control Overview The LabMax Low Level Control…

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions