Search Results

13 - 24 of 56 Products for 'laser chiller' Page 2 of 5 |

laser chiller

2016-Ultrafast-Laser-Systems-Catalog.pdf

2016-Ultrafast-Laser-Systems-Catalog.pdf

…Horizontal Horizontal Horizontal
Voltage 100 to 240
Current Max. (A) 5
Line Frequency (Hz) 50 to 60
Cooling Closed-cycle chiller
Laser Head Dimensions (L x W x H) 609.6 x 427.5 x 162.4 mm (24.0 x 16.8 x 6.4 in.)
excluding handles
Beam Height 120.6 mm (4.75 in.)…

00 Legend Elite Preinstallation.book

00 Legend Elite Preinstallation.book

…Area is clean and large enough to uncrate the laser, power
supplies and chiller.
"Unpacking and
Inspection" on
page 3-1
Utility
Requirements

Seed Laser

Chiller, Seed Laser

Pump Laser

Chiller, Pump Laser

Signal Delay Generator (SDG)

Environmental…

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…Chameleon Discovery
Dual Output, Broadly Tunable Laser for Multiphoton Imaging
Chameleon Discovery
Operating Voltage (VAC) 90 to 250 (auto ranging)
Maximum Operating Current (A)
Power Supply <8 at 90 VAC
Chiller <14 at 90 VAC
MRU <2 at 90 VAC
System…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…shown in Figure 1), they must not reduce the
coolant flow to the laser head, and any heat absorbing/generating
components must come after the laser system.
Chiller Electrical
Supply
A large industrial chiller normally requires a 230 or 480 VAC,
3-phase electrical supply…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…shown in Figure 1), they must not reduce the
coolant flow to the laser head, and any heat absorbing/generating
components must come after the laser system.
Chiller Electrical
Supply
A large industrial chiller normally requires a 230 or 480 VAC,
3-phase electrical supply…

00 LMT Pre.book

00 LMT Pre.book


Input
Assist Gas
Input
Exhaust Sensor
Input
Outlet to Chiller
Remote Interlock
Remote Fan
Regulator Vent
Inlet from Chiller
Control Air Input
Laser Purge Gas
Input
Relay
Pin 1: N.O. Relay Contact
Pin 2: Relay Contact…

00 E-250 Pre.book

00 E-250 Pre.book

…3-1. The delivery system
and/or laser power detector may be connected in parallel auxiliary
loops as long as they do not reduce the required flow to the laser, or
they may be cooled by a separate chiller.
Coolant Temperature At the laser head, the inlet temperature of the cooling…

Avia preinstall.book

Avia preinstall.book

…in the laser head. Connect the plastic tubing from the
chiller to the laser head (flow direction is not important) and fill the
chiller with distilled water. The water control temperature should be
set to maintain the laser baseplate temperature at about 25ºC for best
laser

Quick Setup.fm

Quick Setup.fm

…Installation
1. Hook the laser head to the chiller using the provided hardware, see Figures 1 - 3.
Note, for increased visibility the umbilical has been removed from the laser head in Figure 3.
2. Fill the chiller reservoir with distilled water, start the chiller (see Figure 4), and…

COHR HRNX 355-30 HRR DS 0918 5.pdf

COHR HRNX 355-30 HRR DS 0918 5.pdf


Chiller Water-to-Air or Water-to-Water
Dimensions
Laser Head
Power Supply
SMC Chiller
600 x 780 x 245 mm (23.6 x 30.7 x 9.6 in.)
3U 19" rack
500 x 317 x 615 mm (19.7 x 12.5 x 24.2 in.)
Weight
Laser Head
Power Supply
SMC Chiller
67…

Verdi preinstall.book

Verdi preinstall.book

…titled, "Installing the Chiller".
Installing the
Chiller
Install and setup the chiller in accordance with the user's manual
furnished with the chiller
Final Installation
and Initial
Turn-On
Procedures
After installing the laser head and power supply in…

COHR HRNX SmartCleave DS 0718 3.pdf

COHR HRNX SmartCleave DS 0718 3.pdf


Chiller Water-to-Air or Water-to-Water
Dimensions
Laser Head
Power Supply
SMC Chiller
600 x 780 x 245 mm (23.6 x 30.7 x 9.6 in.)
3U 19" rack
500 x 317 x 615 mm (19.7 x 12.5 x 24.2 in.)
Weight
Laser Head
Power Supply
SMC Chiller
70…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions