Ask a Question
Coherent

Search Results

1 - 12 of 824 Products for 'laser chiller' Page 1 of 69 |

laser chiller

Picosecond laser

Picosecond laser

…space, integration of the laser head, cable lengths, separating the power supplies, electrical plugs etc. Check the mains voltage switch of the chiller (Rapid series). The Hyper Rapid series comes with a chiller with fixed voltage of 230V. Warm-up time The laser system needs a certain initialization…

SUPER RAPID-HE Lasers | Coherent

SUPER RAPID-HE Lasers | Coherent

…weight) 555 x 600 x 685 mm³; 108 kg Warm-Up Time (minutes) <40 from chiller start Industrial, High Repetition Rate Picosecond Laser - The SUPER RAPID series of picosecond lasers is designed for industrial microprocessing. These ps lasers offer a new level of precision and versatility and are ideally…

RAPID Laser | Coherent

RAPID Laser | Coherent

…at 1064 nm (μm) ~1000 750 to 1200 (Laser Head Output) 1500 to 2000 (Module Output) Bore-Sight Accuracy ± 0.5 mm and <5 mrad Warm-Up Time (minutes) <40 from chiller start High-Power Industrial Picosecond Laser - The RAPID series of picosecond lasers are designed for industrial microprocessing.…

HyperRapid NX - Industrial Picosecond Laser

HyperRapid NX - Industrial Picosecond Laser

…efficiency. The HyperRapid NX laser head is a self-contained system where all optical elements, control electronics, and thermo-mechanical management are integrated. It complies with state-of-the-art safety regulation and it is complemented by a selection of off-the-shelf chillers and power supplies…

Picosecond laser

Picosecond laser

…customer RS-232 Not needed Not needed for communication with the laser, yet customer might want to communicate with the chiller. Pump N.A. Provide pump type and specifications Chiller If the SMC chiller was ordered with the laser system, refer to the separate user manual for more information…

Laser Marking Workstations

Laser Marking Workstations

…selected laser source):
* Mark field diameters from 3.5” to 14.9” (88.9mm–380mm)
* Circumferential marking module (oscillating table configuration only)
* Digital readout, motorized or programmable upgrade of Z-Axis
* Refrigerated recirculating water chiller for all LME-RM versions (laser dependent)…

HYPER RAPID Lasers | Coherent

HYPER RAPID Lasers | Coherent

…min from chiller start High Power Industrial Picosecond Laser - The HYPER RAPID family of high power industrial picosecond lasers is the higher power version of the transient-amplifier RAPID-series. THE HYPER RAPID family consists of a 50W and a 100W model and uses a novel LUMERA LASER Technology…

RAPID FX

RAPID FX

…External Comms Ethernet Supply Voltage [100 - 265] VAC Power Consumption <1500W Temperature (non-condensing) - Laser Head +15 to 30°C (59 to 86°F) Temperature (non-condensing) - Chiller +15 to 30°C (59 to 86°F) Vibration <0.15 g Temperature -10 to +50°C (-14 to 122°F) Temperature Gradient 15°C…

Picosecond laser

Picosecond laser

…customer RS-232 Not needed Not needed for communication with the laser, yet customer might want to communicate with the chiller. Pump N.A. Provide pump type and specifications Chiller If the SMC chiller was ordered with the laser system, refer to the separate user manual for more information…

Picosecond laser

Picosecond laser

…customer RS-232 Not needed Not needed for communication with the laser, yet customer might want to communicate with the chiller. Pump N.A. Provide pump type and specifications Chiller If the SMC chiller was ordered with the laser system, refer to the separate user manual for more information…

Picosecond laser

Picosecond laser

…Control (D-Sub 15)" on page 25. Chiller requirements If a customer provided chiller is used, the chiller requirements below must be followed. Flow rate and liquid temperature are measured in the laser head. A communication between the chiller and the laser system is not requested. The cooling…

Picosecond laser

Picosecond laser

…Control (D-Sub 15)" on page 25. Chiller requirements If a customer provided chiller is used, the chiller requirements below must be followed. Flow rate and liquid temperature are measured in the laser head. A communication between the chiller and the laser system is not requested. The cooling…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions