Search Results

1 - 12 of 106 Products for 'laser cleaning' Page 1 of 9 |

laser cleaning

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

…Optic Window Handling
9. Lay the optic window on your clean piece of lint paper and puddle alcohol on it. Let the alcohol soak the window
for a few seconds, just don't let the window dry out. It's important to keep the optic window wet during the
cleaning process. See Figure 9.

Picosecond laser

Picosecond laser


The room, the laser will be located in, should be relatively
clean and free of condensation. For the environmental conditions please refer to section "Ambient condition" on page 6.
l
Adequate table with thread holes (M6) in order to position
and fix the laser head. Refer to…

Excimer laser technology trends

Excimer laser technology trends

…stability as well as in
laser output power achieved over the last two decades are the
combined results of technological advances in laser discharge
preionization, discharge circuit design as well as laser gas
cooling, ventilation and cleaning.
The technique to produce…

Industrial Laser Solutions - January / February 2014

Industrial Laser Solutions - January / February 2014


mechanical techniques, laser cleaning
requires virtually no surface preparation,
is performed dry, doesn't require that
the surface be cleaned of debris afterward, and avoids fber damage if suitable
parameters are chosen. Additionally, laser
processing is compatible…

Coherent Magnum II Laser Operator's Manual

Coherent Magnum II Laser Operator's Manual

…(p. 3-7)
· Servicing the Magnum II laser (p. 3-7)
· Optics and focusing (p. 3-8)
· Cleaning the optics (p. 3-9)
DANGER!
The laser light emitted by this laser may be in the Infrared area
of the electromagnetic spectrum. The laser light may not be
visible to the…

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…Area is clean and large enough to uncrate the laser, power
supplies and chiller.
"Receiving and Inspection" on page 3-1
Utility
Requirements

Seed Laser

Pump Laser

Synchronization & Delay Generator (SDG Elite)

Laptop Computer

Chiller, Pump Laser

Industrial Laser Solutions - November/December 2015

Industrial Laser Solutions - November/December 2015

…often
mechanically complex, requiring downtime for cleaning and
maintenance.
Laser marking is a non-contact method that avoids the problems of contamination and eliminates the cost of consumables.
Furthermore, laser marking generally supports the creation of
high-contrast,…

Laser Focus World - September 2014

Laser Focus World - September 2014


step, the laser head is cycled again (between -10 and +60°C)
and must perform to specification without any realignment.
For a conventional life test, the laser is run without opening
the laser head for cleaning and without any realignment (see
Fig. 3). This laser is operated…

Industrial Laser Solutions - September/October 2015

Industrial Laser Solutions - September/October 2015

…to their final thickness (usually >1µm). The photoresist is stripped and
FIGURE 2. Excimer laser ablation
produces clean, small features in
polyimide.
FIGURE 3. Varying laser fluence enables manipulation of feature
side-wall angles, which can be important in subsequent…

Laser Focus World - August 2017

Laser Focus World - August 2017

…study, a vessel was
embedded deeper in the tissue phantom.
Again, the laser was able to cut precisely and cleanly close to the vessel with
minimal thermal damage.
"The applications for fiber lasers are still
growing rapidly," Wojtkiewicz says. "We
believe that our…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…] Clean third fiber according to fiber cleaning procedure.
(16/24/35 W System).
[ ] Attach fiber 3 to FAP-B #3 (16/24/35 W System).
[ ] Clean fiber 4 according to fiber cleaning procedure
(16/24/35 W System).
[ ] Attach fiber 4 to FAP-B #4 (16/24/35 W System).
[ ] Clean

Laser Focus World - August 2016

Laser Focus World - August 2016

…pulse
cleans out the hole all the way to the underlyingcopper,which--beinguncoated--
reflects the beam and self-terminates the
hole. This method enables rapid production of accurately sized holes with little
post-processing required.
So, CO
2
became the main laser

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions