Ask a Question
Coherent

Search Results

13 - 24 of 156 Products for 'laser lift off' Page 2 of 13 |

laser lift off

ILS Annealing.PDF

lasers to produce high-energy UV pulses is also benefiting other applications in displays and microelectronics manufacturing. For example, excimer lasers are used in mask-based direct patterning of microcircuits for cost-sensitive applications like medical disposables. Here, the excimer laser is…

Picosecond laser

Picosecond laser

…"List of Faults") FACK INT 1 1 -- Acknowledge and clear fault codes Send "FACK=1" to acknowledge faults and return the laser to a ready state if the fault condition is lifted ?FAULTS STR -- Return a list of all fault codes Returns a list of all possible fault and warnings with their numbered codes…

Whitepaper Thin Wafer Laser Debonding.pdf

Whitepaper Thin Wafer Laser Debonding.pdf

…of the laser energy is wasted (since the line goes off the edge of the wafer when the line is anywhere except the very center of the wafer). Conversely, the step-and-repeat method requires less laser power, yet is still capable of reaching up to 40 wafers/hour throughput even at low laser pulse…

Picosecond laser

Picosecond laser

…"List of Faults") FACK INT 1 1 -- Acknowledge and clear fault codes Send "FACK=1" to acknowledge faults and return the laser to a ready state if the fault condition is lifted ?FAULTS STR -- Return a list of all fault codes Returns a list of all possible fault and warnings with their numbered codes…

Picosecond laser

Picosecond laser

…"List of Faults") FACK INT 1 1 -- Acknowledge and clear fault codes Send "FACK=1" to acknowledge faults and return the laser to a ready state if the fault condition is lifted ?FAULTS STR -- Return a list of all fault codes Returns a list of all possible fault and warnings with their numbered codes…

Whitepaper Thin Wafer Laser Debonding.pdf

Whitepaper Thin Wafer Laser Debonding.pdf

…the laser initiated detachment occurs at the glass/adhesive interface. After laser debonding, the glass substrate is lifted off the thinned wafer, leaving some residual adhesive which is then removed using solvents. The Excimer Laser Advantage The most important advantage of 308 nm excimer laser

Whitepaper Thin Wafer Laser Debonding.pdf

Whitepaper Thin Wafer Laser Debonding.pdf

…of the laser energy is wasted (since the line goes off the edge of the wafer when the line is anywhere except the very center of the wafer). Conversely, the step-and-repeat method requires less laser power, yet is still capable of reaching up to 40 wafers/hour throughput even at low laser pulse…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…Chiller One of two different chiller models below will be sent with the system. 8/10 W uses P302-17227. 16/24/35 W uses P307-16273. 1. Lift the top cover off the chiller crate (see Figure 3-4). Do not turn the chiller upside down while you remove it from the crate. NOTICE! The chiller must be…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…Chiller One of two different chiller models below will be sent with the system. 8/10 W uses P302-17227. 16/24/35 W uses P307-16273. 1. Lift the top cover off the chiller crate (see Figure 3-4). Do not turn the chiller upside down while you remove it from the crate. NOTICE! The chiller must be…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…Chiller One of two different chiller models below will be sent with the system. 8/10 W uses P302-17227. 16/24/35 W uses P307-16273. 1. Lift the top cover off the chiller crate (see Figure 3-4). Do not turn the chiller upside down while you remove it from the crate. NOTICE! The chiller must be…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…(arrow down) to confirm the error message and to turn off the red LED. After sufficient coolant has been added, press the ON/OFF button (arrow up) to start the chiller. 6. Confirm that there are no leaks at the water connection sites on the laser head and the chiller. Correct any leaks. 7. When the…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…(arrow down) to confirm the error message and to turn off the red LED. After sufficient coolant has been added, press the ON/OFF button (arrow up) to start the chiller. 6. Confirm that there are no leaks at the water connection sites on the laser head and the chiller. Correct any leaks. 7. When the…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions