Search
Superior Reliability & Performance

  • Lasers and Laser-based Systems
  • Laser Measurement and Control
  • Precision Optics
  • Related Accessories
1 - 10 of 104 Search Results for lasercamhr

1Coherent Inc. LaserCam-HR (RoHS) features a USB 2.0 interface.
LaserCam-HR (RoHS) Including NEW BeamView-USB 4.4.2 software. LMC Product Finder Find a Meter and Sensor Use this finder to select a sensor and then a meter to analyze and display the measurement results. Find a Sensor Use this finder if you already have a meter and you need a replacement sensor.…
Related Searches: lasercam | lasercam-hr | beamview usb | beamview usb 4.4.2

2pdf document  LaserCamHR Manual RevAB Best match in this PDF  |  All matches in this PDF
User Manual LaserCam-HRTM Beam Diagnostics Digital CMOS Camera USB 2.0 User Manual LaserCam-HR Beam Diagnostics Digital CMOS Camera USB 2.0 7470 SW Bridgeport Rd. Portland, OR 97224 LaserCam-HR User Manual ii This document is copyrighted with all rights reserved. Under the copyright laws, this…
Related Searches: lasercam-hr | low distortion faceplate | manual | lasercam

3pdf document  BeamView-USBWithLaserCam-HR QuickStartGuide 1086147RevAE Best match in this PDF  |  All matches in this PDF
Click "Continue Anyway" on this screen. Click "Next" on this screen. Select this radio button and then click "Next." Contact Information For the latest Customer Service information, refer to our website: www.Coherent.com. Coherent and the Coherent Logo are registered trademarks of Coherent, Inc.…
Related Searches: beamview manual | low distortion faceplate | lasercam | beamview usb

400_LaserCamHR.book  (PAGE 21 OF 38)
LaserCam-HR User Manual
12
Pixel Spacing The LaserCam-HR pixel spacing values are shown in
Table 1
Power On LaserCam-HR has no ON/OFF switch. As soon as power
is applied to the camera via the USB 2.0 connection, it
begins operating.
Warm-Up
Time
The…

500_LaserCamHR.book  (PAGE 16 OF 38)
Setup
7
SETUP
This section discusses the following topics:
· Software installation (this page)
· Cabling (page 8)
· Mounting the camera (page 9)
Software
Installation
For complete software installation instructions, refer to
the BeamView-USB With…
Related Searches: beamview software download | beamview

600_LaserCamHR.book  (PAGE 17 OF 38)
LaserCam-HR User Manual
8
Cabling Place the LaserCam-HR at the location where the beam
will be measured. To protect the faceplate from dust,
leave the dust cap installed until ready to make measurements.
USB Cable Connect the USB 2.0 cable to the USB 2.0 connector on

Related Searches: beamview usb

700_LaserCamHR.book  (PAGE 7 OF 38)
LaserCam-HR User Manual
vi
How to Get the Most From Your LaserCam-HR System .............................17
Warranty.........................................................................................................21
Limited Warranty........................................…

800_LaserCamHR.book  (PAGE 26 OF 38)
Operation
17
setscrew and rotating the LDFP housing until the fringes
are no longer present. Slightly turning the camera with
respect to the laser beam may also reduce this effect.
How to Get
the Most From
Your
LaserCam-HR
System
The LaserCam-HR has…

900_LaserCamHR.book  (PAGE 27 OF 38)
LaserCam-HR User Manual
18
· Processor speed--A minimum of 3.3 GHz is
recommended. Faster clock speeds provide higher
frame update rates. Again, "the faster the better."
· Keep all optics clean--Dirty LDFP, beam
sampling, and attenuation optics will distort the

1000_LaserCamHR.book  (PAGE 3 OF 38)
LaserCam-HR User Manual
ii
This document is copyrighted with all rights reserved. Under
the copyright laws, this document may not be copied in whole
or in part or reproduced in any other media without the
express written permission of Coherent, Inc. Permitted copies


Page 1 2 3 4 5 6 7 8 9 10 11>> of 11 | Next


Site Search by  Site Search powered by SLI Systems
.