Search Results

1 - 12 of 12 Products for 'lm-2' Page 1 of 1 |
  • 1

lm-2

High-Sensitivity-Optical-Power-Sensors.pdf

High-Sensitivity-Optical-Power-Sensors.pdf

…IR and LM-2 IR have different spectral ranges.
2 Power range is wavelength dependent. See chart below.
Fiber-Optic Connector
Adapters
1000:1 Attenuator
OP-2 UV/OP-2 VIS/OP-2 IR
LM-2 UV/LM-2 VIS/LM-2 IR
Measurable Power vs.Wavelength
OP-2 VIS and LM-2 VIS

COHERENT LMC 2016-2017 Catalog .pdf

COHERENT LMC 2016-2017 Catalog .pdf

…connection.
Note: Beam position information is not available when using these meters.
This attenuator is used with OP-2 VIS, LM-2 VIS, OP-2 IR and LM-2 IR sensors
to allow operation up to 5W in the visible and 3W in the infrared regions.
The attenuator threads into the sensor in…

ThermalSmartSensorAdapterQuickReferenceGuideRevAC.fm

ThermalSmartSensorAdapterQuickReferenceGuideRevAC.fm

…following Coherent sensors:
SENSOR ITEM NUMBER ROHS ITEM NUMBER
Beam Finder 33-1215-000 1098427
LM-2 IR 33-0944-000 1098342
LM-2 UV 33-0951-000 1098390
LM-2 VIS 33-0936-000 1098298
LM-3 HTD 33-7931-000 1098328
LM-10 HTD 33-7923-000 1098304
LM-20 HTD…

Vitara Preinstall.book

Vitara Preinstall.book

…Lens Tissues
[ ] Powderless latex or nitrile gloves
Laser Equipment
[ ] Power meter and head (e.g., Coherent FieldMate with LM10,
LM2 heads).
[ ] Intensity calibrated spectrometer (e.g., StellarNet Blue-wave
NIR2-14).
[ ] A beamsplitter to send part of the beam to…

LabMax-Pro SSIM User Manual

LabMax-Pro SSIM User Manual

LabMax-Pro SSIM User Manual
3 - 2
Sensor
Compatibility
PowerMax-Pro, PM model thermopiles, LM model thermopiles,
OP-2 & LM-2 optical sensors, and DB-25 EnergyMax sensors.
USB/RS-232 LabMax-Pro requires a USB 2.0 High-Speed USB to communicate
with the PC.…

Thermal SmartSensor Adapter DSrevA 4.qxd

Thermal SmartSensor Adapter DSrevA 4.qxd

…following
Coherent sensors:
Sensor Part Number RoHS Item Number
Beam Finder 33-1215-000 1098427
LM-2 IR 33-0944-000 1098342
LM-2 UV 33-0951-000 1098390
LM-2 VIS 33-0936-000 1098298
LM-3 HTD 33-7931-000 1098328
LM-10 HTD 33-7923-000 1098304
LM-20 HTD…

Libra PreInstallation.book

Libra PreInstallation.book

Lens Tissues

Powderless latex or nitrile gloves
Laser Equipment

Power meter and head (e.g., Coherent FieldMate with LM10,
LM2 heads).

An oscilloscope (300 MHz or higher)
Table 3-5. Pre-installation Checklist
ACTIVITYAND
EQUIPMENT
GENERAL REQUIREMENTS…

LabMax-Pro-Data-Sheet FORMFIRST.pdf

LabMax-Pro-Data-Sheet FORMFIRST.pdf


at 10 Hz speed 0.1
at 20 KHz high speed 0.2
Sensor Compatibility PM Model Thermopile; PowerMax-Pro; LM Model Thermopile, OP-2 & LM-2 Optical,
DB-25 EnergyMax pyroelectric
Measurement Range Sensor dependent (reference sensor specifications)
Accuracy (%)
Digital…

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

…measured with ModeMaster with 90/10 clip levels.
4 Polarization measurement is max./min. power with polarizer at 32 in. from laser with LM-2 power head at 37 in. from laser.
5 Static alignment tolerances are relative to the right bottom edge (in beam direction).
6 Electro-Static…

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…measured with ModeMaster with 90/10 clip levels.
4 Polarization measurement is max./min. power with polarizer at 32 in. from laser with LM-2 power head at 37 in. from laser.
5 Static alignment tolerances are relative to the right bottom edge (in beam direction).
6 Electro-Static…

COHR CUBE DS 0818 4.pdf

COHR CUBE DS 0818 4.pdf

…measured with ModeMaster with 90/10 clip levels.
4 Polarization measurement is max./min. power with polarizer at 32 in. from laser with LM-2 power head at 37 in. from laser.
5 Static alignment tolerances are relative to the right bottom edge (in beam direction).
6 Electro-Static…

Industrial Laser Solutions - March/April 2016

Industrial Laser Solutions - March/April 2016

18 Industrial Laser Solutions MARCH/APRIL 2016 www.industrial-lasers.com
t e c h n o l o g y r e p o r t
Applications
Currently, KSD GmbH is employing
the R:LM2 process in the production cladding of gaskets for industrial faucets, and for the bearing surfaces of races in sliding…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions