Search
Superior Reliability & Performance

  • Lasers and Laser-based Systems
  • Laser Measurement and Control
  • Precision Optics
  • Related Accessories
1 - 10 of 53 Search Results for mode master

1pdf document  Mode Master White Paper July 2011 final Best match in this PDF  |  All matches in this PDF
www.Coherent.com I lmc.sales@coherent.com I (800) 343-4912 I (408) 764-4042 1 White Paper Mode Quality (M2 ) Measurement Improves Laser Performance The laser mode quality factor (M2 ) provides a highly useful means of predicting laser beam propagation and focusing characteristics for both laser manufacturers…
Related Searches: m2 | modemaster | beam master

2pdf document  man green-powerline Best match in this PDF  |  All matches in this PDF
…in section 3.1 to properly connect the laser to either CW (Continuous Wave) mode or Modulation mode. The modulation source is connected to the DB9 connector. You can modulate the laser in one of two modes: 3.4.1 Standard Mode: Linear modulation The modulation source is a variable amplitude signal. It…
Related Searches: laser cooler | viewing card | powerline | lasiris powerline

3pdf document  80390-037e-LFW Best match in this PDF  |  All matches in this PDF
…-laser configuration-- particularly for marking applications-- can take on another form called a master-oscillator power amplifier (MOPA). Instead of the fiber Bragg gratings at the start, a single-mode laser diode is followed by one or two power amplifiers. These amplifiers are made up of the same active…
Related Searches: mopa | permalign | diode-pumped solid-state | beam master

4pdf document  SemiManufMagRev2 Best match in this PDF  |  All matches in this PDF
…addresses these various requirements by using a two-chamber construction in an architecture called MORRA (master oscillator-regenerative ring amplifier) (see Figure 1). The first chamber is a master oscillator, which produces light with the desired spectral characteristics. The second chamber is a regenerative…
Related Searches: wafer inspection | indigo | sapphire scribing | 257 nm laser

5Paladin355_DS  (PAGE 2 OF 2)

(W)
Paladin 355-4000 >4
Paladin 355-8000 >8
Repetition Rate (MHz) 80 ±1 MHz
Pulse Length (ps) >15 @ 1064 nm
Spatial Mode TEM00
M2 <1.2
Beam Diameter (mm)
Paladin 355-4000 1 ±10%
Paladin 355-8000 1 ±15%
Beam Divergence (µrad) <550
Beam Ellipticity…

6pdf document  instruction manual Best match in this PDF  |  All matches in this PDF
…the laser. For more information about the safety key box, refer to section 5.5. 3.6 Modulating the Laser The standard laser runs on Continuous Wave mode. However, lasers can have two power adjustment options; these options must be chosen at the time of order. (1) Power Adjustment Potentiometer: The laser…
Related Searches: cdrh class | gll | laser cooler | lasiris

7pdf document  60390-345e-LFW Best match in this PDF  |  All matches in this PDF
…OPS advantage is its longitudinal-mode characteristics, which result in low noise in the frequency-doubled output. Intracavity-doubled continuous-wave (CW) lasers often suffer from mode noise because power oscillates dynamically between different longitudinal modes. Because second-harmonic-generation…
Related Searches: 488 nm laser | birefringent filter | ophthalmic lasers | applications lab

8PaladinAdvanced355_DS  (PAGE 2 OF 2)
…Advanced 355-10000 >10
Paladin Advanced 355-16000 >16
Repetition Rate (MHz) 80 ±1 MHz
Pulse Length (ps) >15 @ 1064 nm
Spatial Mode TEM00
M2 <1.2
Beam Diameter (mm)
Paladin Advanced 355-8000/10000 1 ±15%
Paladin Advanced 355-16000 1.35 ±15%
Beam Divergence…

9untitled  (PAGE 23 OF 136)
…achieved by varying the materials used in this device and doubling the frequency of the laser beam. The
OPS is a compact, rugged, high power, single-mode laser. Our frequency doubled OPS lasers are all solid-state
devices operating continuously in the blue region of the optical spectrum and are particularly…

10pdf document  HighLight 4000L Preinstallation Manual Best match in this PDF  |  All matches in this PDF
…Industrial Laser System is a Class 4 direct-diode laser system capable of delivering up to 4000 Watts of average power in pulsed or continuous wave modes. The laser is intended to be used for cladding, heat treating, and welding applications in an industrial setting. The laser system consists of three…
Related Searches: laser wire stripper | rf power supply | tube | 4 axis mount


Page 1 2 3 4 5 6 of 6 | Next


Site Search by  Site Search powered by SLI Systems
.