1 - 10 of 699 Search Results for pointer
|
|
1.
Laser_Cooling_Water_Guidelines
(PAGE 9 OF 34)
|
|
|
... in problems such as: · Drift in the laser output power · Frequency drift in single-frequency operation · Drift in the output beam direction (beam pointing) Long term flow rate stability can be measured using electronic pressure gauges attached to a chart recorder, or by manually recording the data over ...
|
|
|
|
|
2.
Compass_1064_2500_4000
(PAGE 1 OF 2)
|
|
... mW Spatial Mode TEM00 TEM00 Wavelength Stability <1 cm-1 not specified Beam Diameter @ 1/e2 0.4 mm 0.3 mm Beam Divergence <3.5 mrad <5 mrad Pointing Stability <±5% of beam divergence <±1% of beam divergence Noise (10 Hz to 100 kHz) < 1.0% (rms) < 1.0% (rms) Long-term Power Stability ...
Related Searches: compass 1064
|
|
|
|
|
3.
Verdi_V8V10
(PAGE 2 OF 2)
|
|
... Output Power (W) >8 >10 Wavelength (nm) 532 Linewidth1 (MHz) <5 Beam Diameter2 (mm) 2.25 ±10% Beam Divergence3 (mrad) <0.5 M2 <1.1 Pointing Stability 4 (rad/°C) <2 Power Stability5 ±1% Noise6 (RMS) <0.03% Polarization Vertical, >100:1 Operating Voltage (VAC) 100 to 240 Operating ...
Related Searches: verdi-v10 | verdi v10 | coherent verdi v10
|
|
|
|
|
4.
packagingrequirements
(PAGE 6 OF 25)
|
|
|
... is in the Regulations and further guidance as to the interpretation of packaging has been published by the Environment Agencies (see contact points). However, anything recognised as packaging and in use as packaging would in general be likely to be covered by these Regulations. [Following a revision ...
|
|
|
|
|
5.
LTJ_0108_CO2_Laser
(PAGE 2 OF 2)
|
|
|
... both laser stability and lifetime. plus the rF power supply is integrated in the laser head, eliminating the rF umbilical as a possible failure point. as a result every Diamond C laser is guaranteed to meet or exceed performance specifications for a minimum of 24 months, with no need for gas refilling ...
|
|
|
|
|
6.
BBO_DS
(PAGE 2 OF 2)
|
|
|
... BaB2O4 Crystal Structure Trigonal , 3m Optical Symmetry Uniaxial Negative (no > ne) Lattice Constants (Å) a = b = 12.532; c = 12.717; Z=6 Melting Point (°C) 1095 ± 5° Specific Heat (J/cm2. °K) 1.91 Phase Transition ( <-> ) (°C) 925 ± 5° Density (g/cm3) 3.85 Hardness (Mohs) 3.5 - 4.5 Youngs ...
|
|
|
|
|
7.
Sabre_MotoFreD_Preinstallation
(PAGE 18 OF 26)
|
|
|
... whose performance depends on its environment. Vibrations can be transmitted to the laser head from the surface on which it rests, causing beam pointing instability and power fluctuations. To minimize vibrations, the laser head should be placed on a stabilized optical table and isolated from mechanical ...
|
|
|
|
|
8.
Laser_Cooling_Water_Guidelines
(PAGE 11 OF 34)
|
|
|
... any effects due to vibrations or excessive pressure. Water Temperature Specification The temperature of the cooling water is specified at the point where the water enters the laser system. All Innova lasers have the same specification, presented in Table 2. Temperature Sensors The Innova series lasers ...
|
|
|
|
|
9.
pdf_127
(PAGE 2 OF 12)
|
|
... region. After each laser pulse, certain pre-defined criteria are evaluated in the software. When these criteria are exceeded, the laser stops and is pointed at a new position, where the cleaning process starts again. Detailed Material Analysis Required The knowledge regarding paint materials, processes ...
Related Searches: compex 205
|
|
|
|
|
10.
OPSL-532_577_DS
|
Best match in this PDF
|
All matches in this PDF
|
|
... ) 0.132 0.122 Location (mm) -632,3 Beam Divergence Horizontal (FW, 1/e2, mrad) 202 Vertical (FW, 1/e2, mrad) 142 M2 Horizontal <7 Vertical <4 Pointing Stability (rad/°C) <304 Noise 10 Hz to 10 MHz (%, rms) <0.52 10 Hz to 5 kHz (%, peak-to-peak) <10 Polarization Ratio >100:1, horizontal ...
|
|
Coherent Contact Information