Superior Reliability & Performance

• Lasers and Laser-based Systems
• Laser Measurement and Control
• Precision Optics
• Related Accessories

---

1.    HighPeakPowerSolidStateLaserforMicromachiningofHardMaterialsRev2 Best match in this PDF  |  All matches in this PDF …Lambda Physik Gator series. This series consists of models with output powers ranging from 3 to >28 watt and wavelengths of 1064, 532 and 355 nm. Since all Gator models deliver short pulses of about 15 ns. the very high peak power of up to 24 GW/cm² is achieved. Model Wavelength Average Power at 10 kHz… Related Searches: 355 nm diode | trepanning head | 355 nm laser | silicon drilling

2.  HighPeakPowerSolidStateLaserforMicromachiningofHardMaterialsRev2.pdf  (PAGE 3 OF 9) …Physik Gator series. This series consists of models with output powers ranging from 3 to >28 watt and wavelengths of 1064, 532 and 355 nm. Since all Gator models deliver short pulses of about 15 ns. the very high peak power of up to 24 GW/cm² is achieved. Model Wavelength Average Power … Related Searches: powergator

3.  Coherent, Inc. 10-K  (PAGE 11 OF 93) …COMpex Excimer Metrology (Measuring Technology) OPTex, COMPex NovaTech Excimer Excimer Spectroscopy COMPex Gator family, Chameleon Mira, RegA, OPO 899, MBR, MBD Innova family Excimer DPSS Ultrafast CW Tunable Ion Physical… Related Searches: excimer | labmaster

4.    pdf 128 Best match in this PDF  |  All matches in this PDF …Experimental The laser source consisted of sidepumped, q-switched Nd:YAG oscillator (Lambda Physik's Gator) followed by a diodepumped amplifier. The oscillator produced 15 ns pulses in TEM00 beam with an average power of 10 W at 1064 nm and a nominal repetition rate of 10 kHz. The amplifier output was 28 W at… Related Searches: 355 nm laser | beam quality factor | co2 pulse laser | ultrasonic

5.    ComparisonExcimerLaserSolidStateLaserRev2 Best match in this PDF  |  All matches in this PDF …well adapted to applications where the shorter wavelengths are an advantage. Excimer lasers provide a wide range of processing power, with average range of processing powers up to 300 W, repetition rates to 4 kHz, energies higher than 1 J and pulse lengths from 10 to 250 ns. The most widely used wavelengths… Related Searches: 193 nm laser | 266 nm | kapton | excimer

6.  06smallholes.indd  (PAGE 1 OF 8) …microdrilling and other micromachining applications. The Gator (photo on page 77) is a compact, diode-pumped solid-state laser (DPSSL) made by Lambda PhysikInc.,Ft.Lauderdale,Florida.Itoffers a combination of high peak power, high repetition rates and beam quality that makes it…

7.  HighPeakPowerSolidStateLaserforMicromachiningofHardMaterialsRev2.pdf  (PAGE 4 OF 9) … GATOR 532 / POWERGATOR 532 8 -16 µm spot GATOR 1064 / POWERGATOR 1064 16 - 32 µm spot Table 3: Typical spot diameters d for f/D = 10 to 20 for the different Gator models. 3. RESULTS AND DISCUSSION The influence of different laser parameters such as wavelength and power have…

8.    NonTraditionalMethodsforMakingSmallHolesRev2 Best match in this PDF  |  All matches in this PDF …tool for microdrilling and other micromachining applications. The Gator (photo on page 77) is a compact, diode-pumped solid-state laser (DPSSL) made by Lambda PhysikInc.,Ft.Lauderdale,Florida.Itoffers a combination of high peak power, high repetition rates and beam quality that makes it suitable for… Related Searches: alumina drilling | ceramic | fiber optic taper | pinhole

9.  HighPeakPowerSolidStateLaserforMicromachiningofHardMaterialsRev2.pdf  (PAGE 1 OF 9) …beam focusability. The Gator series of lasers have been specifically designed for micromachining of hard materials including cutting and drilling of both through, as well as, blind holes and slots. The distinguishing characteristic of the Gator is its high peak power, resulting from its short… Related Searches: powergator | fiber optic taper

10.  06smallholes.indd  (PAGE 2 OF 8) …plus a muchshorterwavelength results in a greater cuttingefficiency.Lessheat isgeneratedinthepartas well:Becauseofthehigh power intensity created by the short pulse, much of the material is removed in a photo-ablative state rather than a thermal melting state,…

---

Search Suggestions: excimer | trepanning head | sapphire | 266 nm | excimer lamp | microlas | lambda physik krf | fiber optic taper | uv lasers | powergator

Page 1 2 of 2 | Next

Site Search by