1 - 10 of 116 Search Results for screw
|
|
1.
Diamond_E-400_Preinstallation_RevAA
(PAGE 22 OF 31)
|
|
|
... , clean and flat surface, such as an optical table. 13. Uncrate the remaining crates in a similar fashion and this will require the removal of wood screws at the bottom of the crate, similarly to the Diamond E-400 crate (Step1). Figure 10. Forklift
|
|
|
|
|
2.
cqeofiDS
(PAGE 1 OF 2)
|
|
... units are precision-machined so that the beam exits within 0.001 radians of the laser beam's original direction. Three, 10-32 brass-tipped set-screws maintain the CQE and OFI's reference plane to the front of the laser. These screws can be adjusted to optimize beam alignment through beam delivery optics ...
Related Searches: optical isolator
|
|
|
|
|
3.
EnergyMax Heat Sink Accessories
|
|
... rates or at higher energy levels. The heat sinks are easily installed by threading them onto the back of a sensor housing with a 1/4-20 cap screw conveniently contained within the heat sink. The Small and Medium models are for use with sensors that have a 25mm diameter aperture, and ...
Related Searches: j-25mb-le
|
|
|
|
|
5.
Avia_266_Preinstallation
(PAGE 18 OF 38)
|
|
|
... (Note 1) Mains IEC-320 C-14 Mating Power Cable Supplied Remote Contact Factory 1. Connectors listed include crimp pins, but not backshells, jack screws, or other accessories. 2. Equivalent connectors from any manufacturer are acceptable.
|
|
|
|
|
6.
ACF2C21
(PAGE 4 OF 4)
|
|
|
MOUNTING HOLES 8-32UNC-2B X X .44 INCH DEEP POLARIZATION DIRECTION DC POWER IN SCREW TERMINAL GROUND CONTROL 0.250 INCH PIPE THREAD FOR COOLING WATER IN/OUT 0.125 INCH PIPE THREAD FOR PARALLEL WATER FLOW TO ACCESSORIES 44.45 mm (1.75 in.) 19.05 mm (0.75 in.) 50.8 mm (2.00 in) 760.48 mm (29.94 in.) ...
|
|
|
|
|
7.
Verdi_V8-V10_Preinstallation
(PAGE 9 OF 18)
|
|
... shipping crate. Place the laser head on its side and on a protected surface to avoid scratching the cover as shown on Figure 1-3. Remove the three screws (Figure 1-3, item 2) securing the protective plastic cover (item 4) to the laser head baseplate. Any scratches, damage, or contamination of the baseplate ...
Related Searches: verdi v10 manual
|
|
|
|
|
8.
Verdi_V8-V10_Preinstallation
(PAGE 10 OF 18)
|
|
|
Verdi V-8/V-10 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective plastic ...
|
|
|
|
|
10.
PulseLife_CCP_DS
(PAGE 1 OF 2)
|
|
|
... Superior Reliability & Performance Mechanical Specifications Emitter Height Top Surface of Anode Serial Number Anode Cathode #6-32 Cathode Screw #4-40 Shorting Screw 10.7 mm (0.42 in.) 7.95 mm (0.313 in.) 14.2 mm (0.56 in.) 12.4 mm (0.49 in.) 6.1 mm (0.24 in.) 14 mm (0.55 in.) 8.1 mm (0.32 in.) ...
|
|
Coherent Contact Information