---

1.    Verdi_V2-V5-V6_Preinstallation Best match in this PDF  |  All matches in this PDF Preinstallation Manual VerdiTM V-2/V-5/V-6 Diode-Pumped Lasers 5100 Patrick Henry Drive Santa Clara, CA 95054 Verdi V-2/V-5/V-6 Laser Preinstallation Manual ii This document is copyrighted with all rights reserved. Under the copyright laws, this document may not be copied in whole or in part or reproduced ... Related Searches: verdi v2 manual | verdi v6 | water chiller verdi

2.  Diode-Pumped Solid-State (DPSS) Laser Systems Guidelines ... environments Highest level of post-sale customer care Long-term customer relationships Literature & Documentation . AVIA 266 Preinstallation Manual AVIA 355-355X Preinstallation Manual VERDI V-18 Preinstallation Manual VERDI V-2/V-5/V-6 Preinstallation Manual VERDI V-8/V-10 Preinstallation Manual ... Related Searches: verdi | avia | verdi manual | verdi v10 manual

3.    Verdi_V2-V5-V6_Preinstallation  (PAGE 9 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 3 The laser head is shipped with a protective plastic plate installed over the baseplate. Leave the plastic plate in place until laser head is ready for installation. 1. Remove the packing material from the riser/heat sink (Figure 1-2). 2. Insert two dowel ...

4.    Verdi_V2-V5-V6_Preinstallation  (PAGE 10 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet (if included) 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material ... Related Searches: verdi laser manual

5.    Verdi_V2-V5-V6_Preinstallation  (PAGE 11 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 5 6. Proceed to the paragraph titled, "Installing the Power Supply". The riser/heat sink clamps and chiller connection will be installed during the final installation procedures. Installing the Power Supply 1. Move the power supply to an accessible ...

6.    Verdi_V2-V5-V6_Preinstallation  (PAGE 12 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 6 Each customer must inspect the power cord and install the proper connector if necessary. The connector should be installed in a properly grounded outlet with a maximum of 10 Ampere service @ 110 V and 11 Ampere service @ 220 V for proper overcurrent ... Related Searches: verdi laser manual

7.    Verdi_V2-V5-V6_Preinstallation  (PAGE 13 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 7 7. Perform the procedure in paragraph titled, "Turn-on (Cold-Start)" in the Operator's Manual. External Interlock The system will not operate with the interlock open. An interlock connector is located on the power supply rear panel. The interlock ... Related Searches: verdi v5 | wiring diagrams

8.    Verdi_V2-V5-V6_Preinstallation  (PAGE 14 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 8 5. The interlock circuit in Verdi operates from a +/-12 VDC circuit. Its current is limited to around 1 mA. For these ratings, a "dry-circuit" type switch will give the most reliable operation. Figure 1-6. Interconnect Diagram Table 1-1. Utility ...

9.    Verdi_V2-V5-V6_Preinstallation  (PAGE 15 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 9 Dimensions Table 1-2. Environmental Requirements PARAMETER REQUIREMENT Operating temperature 15 to 35°C (59 to 95°F) Relative humidity 5 to 95% (non condensing) Altitude Sea level to 10,000 feet Figure 1-7. Laser Head Dimensions Related Searches: verdi v2

10.    Verdi_V2-V5-V6_Preinstallation  (PAGE 16 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 10 Figure 1-8. Power Supply Dimensions

---

Search Suggestions: verdi manual | verdi v2 manual | verdi v6 | water chiller verdi | verdi | avia | verdi v5 | mira | manual | verdi v10 manual

Page 1 2 of 2 | Next

Site Search by

Coherent Contact Information