---

1.    Verdi_V2-V5-V6_Preinstallation  (PAGE 6 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual vi Related Searches: verdi v5 manual

2.    Verdi_V2-V5-V6_Preinstallation  (PAGE 7 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 1 Introduction The purpose of this document is to assist the user in establishing a suitable location and operating environment for optimum Verdi V-2/V-5/V-6 performance. Receiving and Inspection Inspect shipping containers for signs of rough handling ...

3.    Verdi_V2-V5-V6_Preinstallation  (PAGE 8 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 2 1. Riser/heat sink installation hardware 2. Operator's manual 3. AC power cord 4. Power supply key 5. Installation kit case 6. Interlock-disassembled 7. Fuses and instructions 8. FAP-I installation hardware, including shorting clips, end caps, etc. 9 ... Related Searches: verdi laser manual | verdi v5 manual

4.    Verdi_V2-V5-V6_Preinstallation  (PAGE 9 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 3 The laser head is shipped with a protective plastic plate installed over the baseplate. Leave the plastic plate in place until laser head is ready for installation. 1. Remove the packing material from the riser/heat sink (Figure 1-2). 2. Insert two dowel ...

5.    Verdi_V2-V5-V6_Preinstallation  (PAGE 10 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet (if included) 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material ... Related Searches: verdi laser manual

6.    Verdi_V2-V5-V6_Preinstallation  (PAGE 11 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 5 6. Proceed to the paragraph titled, "Installing the Power Supply". The riser/heat sink clamps and chiller connection will be installed during the final installation procedures. Installing the Power Supply 1. Move the power supply to an accessible ...

7.    Verdi_V2-V5-V6_Preinstallation  (PAGE 12 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 6 Each customer must inspect the power cord and install the proper connector if necessary. The connector should be installed in a properly grounded outlet with a maximum of 10 Ampere service @ 110 V and 11 Ampere service @ 220 V for proper overcurrent ... Related Searches: water chiller

8.    Verdi_V2-V5-V6_Preinstallation  (PAGE 13 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 7 7. Perform the procedure in paragraph titled, "Turn-on (Cold-Start)" in the Operator's Manual. External Interlock The system will not operate with the interlock open. An interlock connector is located on the power supply rear panel. The interlock ...

9.    Verdi_V2-V5-V6_Preinstallation  (PAGE 14 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 8 5. The interlock circuit in Verdi operates from a +/-12 VDC circuit. Its current is limited to around 1 mA. For these ratings, a "dry-circuit" type switch will give the most reliable operation. Figure 1-6. Interconnect Diagram Table 1-1. Utility ...

10.    Verdi_V2-V5-V6_Preinstallation  (PAGE 15 OF 18) Verdi V-2/V-5/V-6 Laser Preinstallation Manual 9 Dimensions Table 1-2. Environmental Requirements PARAMETER REQUIREMENT Operating temperature 15 to 35C (59 to 95F) Relative humidity 5 to 95% (non condensing) Altitude Sea level to 10,000 feet Figure 1-7. Laser Head Dimensions

---

Page 1 2 3 of 3 | Next

Site Search by

Coherent Contact Information