Search
Superior Reliability & Performance

  • Lasers and Laser-based Systems
  • Laser Measurement and Control
  • Precision Optics
  • Related Accessories
1 - 10 of 11 Search Results for vswr
1.  pdf document  Diamond Integrators Guide RevAA Best match in this PDF  |  All matches in this PDF
…drive 10 k load. A voltage level greater than 1.0 V may indicate either a bad laser head, a bad RF cable, or both. 6 VSWR Fault Open collector output Will sink 25 mA of current when an VSWR fault occurs. This indicates an excessive mismatch between the laser head and the RF power supply. 7 - Not currently…
Related Searches: recirculator | oem controller | oem manual | diamond manual

2.  Coherent Inc. CO2 RF Warning Faults – DIAMOND OEM Laser
…than 1 ms pulse width. * 2nd Check – VSWR indicator on. Indicated by a pulse waveform being present at pin 11 of the 25 pin connector. Normal indication is a DC or ground signal. Often will light with Forward and Reflected. Forget about Forward light if VSWR is on. Most probable causes are the RF cable…
Related Searches: rf amplifier | rf co2 lasers | operation manual

3.  Coherent Inc. CO2 RF Warning Lights On
…The Coherent Product Support Team is dedicated to your success and welcomes your service-related questions, comments, or concerns. Related symptoms; VSWR light on, Duty Cycle light on, Forward light on, Reflected light on. See Chapter titled "Maintenance and Troubleshooting" in the Operator's Manual for…

4.  pdf document  DIAMOND E1000 premanual Best match in this PDF  |  All matches in this PDF
…1 0 0 1 0 242 0xF2 RTIO_FPGA_STATUS (2ND BYTE, MODULATING FAULTS) NOT USED NOT USED NOT USED SIMMER SHUTTER POSITION* SHUTTER COMMAND** DUTY CYCLE VSWR DECIMAL HEX 0 0 0 0 0 0 0 1 1 0x01 0 0 0 0 0 0 1 0 2 0x02 0 0 0 0 0 0 1 1 3 0x03 0 0 0 0 0 1 0 0 4 0x04 0 0 0 0 0 1 0 1 5 0x05 0 0 0 0 0 1 1 1 7 0x07…
Related Searches: shutter kits | laser beam diagnostics | dc power supply | diamond 84

5.  00_Diamond_Int.book  (PAGE 46 OF 55)
…conditions; a Duty Cycle Limit signal indicates that there
is a difference between the commanded output and the actual output.
VSWR Limit (Pin 11+, Pin 24-)
The VSWR (voltage standing wave ratio) limit signal is issued when
the ratio of the reflected RF to the forward RF exceeds a preset limit…
Related Searches: gem 100 manual

6.  00_Diamond_Int.book  (PAGE 46 OF 55)
…conditions; a Duty Cycle Limit signal indicates that there
is a difference between the commanded output and the actual output.
VSWR Limit (Pin 11+, Pin 24-)
The VSWR (voltage standing wave ratio) limit signal is issued when
the ratio of the reflected RF to the forward RF exceeds a preset limit…
Related Searches: gem 100 manual

7.  00_Diamond_Int.book  (PAGE 42 OF 55)
…voltage level greater than 1.0 V may indicate either a bad laser head,
a bad RF cable, or both.
6 VSWR Fault
Open collector output
Will sink 25 mA of current when an VSWR fault occurs. This indicates an excessive mismatch between the laser head and the RF power
supply.
…
Related Searches: rf power supply

8.  00_Diamond_Int.book  (PAGE 42 OF 55)
…voltage level greater than 1.0 V may indicate either a bad laser head,
a bad RF cable, or both.
6 VSWR Fault
Open collector output
Will sink 25 mA of current when an VSWR fault occurs. This indicates an excessive mismatch between the laser head and the RF power
supply.
…
Related Searches: rf power supply

9.  00_Diamond_Int.book  (PAGE 54 OF 55)
…4
Sealing 24
Seals
Moving beams 26
Shutter 19, 40
System integrators 2
V
View optics 10
Viewports 10
VSWR limit 40
W
Warning logotype 6, 10
Water cooling 17
Water flow
Interlock 18
Switch 40, 46
Workplace safety 4
…

10.  00_Diamond_Int.book  (PAGE 54 OF 55)
…4
Sealing 24
Seals
Moving beams 26
Shutter 19, 40
System integrators 2
V
View optics 10
Viewports 10
VSWR limit 40
W
Warning logotype 6, 10
Water cooling 17
Water flow
Interlock 18
Switch 40, 46
Workplace safety 4
…

Page 1 2 of 2 | Next


Site Search by  Site Search powered by SLI Systems
.