Ask a Question
Coherent
Search Results
Refine

Result Type

1 - 12 of 87 Products for 'vswr fault' Page 1 of 8 |

vswr fault

00 E-250 Pre.book

00 E-250 Pre.book

Fault occurs, it will be a transient condition, and will only be seen briefly when the laser has been turned on after being off for an extended period of time. Note: although Simmer Fault and VSWR Fault share the same output pins, Simmer Fault can only occur when modulation is not applied, and VSWR

00 E-250 Pre.book

00 E-250 Pre.book

Fault occurs, it will be a transient condition, and will only be seen briefly when the laser has been turned on after being off for an extended period of time. Note: although Simmer Fault and VSWR Fault share the same output pins, Simmer Fault can only occur when modulation is not applied, and VSWR

00 E-250 Pre.book

00 E-250 Pre.book

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

00 E-250 Pre.book

00 E-250 Pre.book

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

00 E-250 Pre.book

00 E-250 Pre.book

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…Amplifier Output Signals - VSWR Fault Modulation (pin 7 referenced to pin 14) 1. If VSWR fault is detected on the first pulse, Analog Forward (pin 1 referenced to pin 14) RF is applied to the laser during a HI condition. 2. Subsequent pulses are supressed until the VSWR controller algorithm…

00 E-250 Pre.book

00 E-250 Pre.book

Fault occurs, it will be a transient condition, and will only be seen briefly when the laser has been turned on after being off for an extended period of time. Note: although Simmer Fault and VSWR Fault share the same output pins, Simmer Fault can only occur when modulation is not applied, and VSWR

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions